Iei-integration ECN-360A-D2550 User Manual

ECN-360A-D2550 Embedded System Page i IEI Technology Corp. User Manual , MODEL: ECN-360A-D2550 Embedded System with Intel® dual core Atom™ D2550 P

ECN-360A-D2550 Embedded System Page x Figure C-28: Press any key to continue ...

ECN-360A-D2550 Embedded System Page 89 Figure C-2: Launching the Recovery Tool Step 3: The recovery tool setup menu is shown as below. Figure C

ECN-360A-D2550 Embedded System Page 90 Figure C-4: Command Prompt Step 5: The command prompt window appears. Type the following commands (marked i

ECN-360A-D2550 Embedded System Page 91 Figure C-5: Partition Creation Commands

ECN-360A-D2550 Embedded System Page 92 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press an

ECN-360A-D2550 Embedded System Page 93 C.2.4 Building the Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the sy

ECN-360A-D2550 Embedded System Page 94 Step 5: The Symantec Ghost window appears and starts configuring the system to build a recovery partition. I

ECN-360A-D2550 Embedded System Page 95 C.2.5 Create Factory Default Im a g e NOTE: Before creating the factory default image, please configure th

ECN-360A-D2550 Embedded System Page 96 Figure C-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (Figure C-

ECN-360A-D2550 Embedded System Page 97 Figure C-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as sho

ECN-360A-D2550 Embedded System Page 98 Figure C-16: File Name to Copy Image to Step 8: When the Compress Image screen in Figure C-17 prompts, clic

ECN-360A-D2550 Embedded System Page xi Lis t of Tables Table 1-1: Model Variations ...

ECN-360A-D2550 Embedded System Page 99 Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure C-18: Image

ECN-360A-D2550 Embedded System Page 100 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. St ep

ECN-360A-D2550 Embedded System Page 101 Figure C-22: Auto Recovery Utility Step 3: Reboot the system from the recovery CD. When prompted, press an

ECN-360A-D2550 Embedded System Page 102 Step 5: The Symantec Ghost window appears and starts configuring the system to build an auto recovery parti

ECN-360A-D2550 Embedded System Page 103 Step 7: The Symantec Ghost starts to create the factory default image (Figure C-27). Figure C-27: Image Cr

ECN-360A-D2550 Embedded System Page 104 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced iEi Feature Auto Recove

ECN-360A-D2550 Embedded System Page 105 Step 1: Hardware and BIOS setup. Refer to Section C.2.1. Step 2: Install Linux operating system. Make sure

ECN-360A-D2550 Embedded System Page 106 DISKPART>sel disk 0 DISKPART>create part pri size= ___ DISKPART>assign letter=N DISKPART>ex

ECN-360A-D2550 Embedded System Page 107 Figure C-31: Access menu.lst in Linux (Text Mode) Step 6: Modify the menu.lst as shown below. Step 7:

ECN-360A-D2550 Embedded System Page 108 C.5 Recovery Tool Functions After completing the initial setup procedures as described above, users can acce

ECN-360A-D2550 Embedded System Page 1 Chapter 1 1 Introduction

ECN-360A-D2550 Embedded System Page 109 WARNING: All data in the system will be deleted during the system recovery. Please backup the system files

ECN-360A-D2550 Embedded System Page 110 Figure C-35: Recovery Complete Window C.5.2 Backup System To backup the system, please follow the steps bel

ECN-360A-D2550 Embedded System Page 111 Figure C-37: System Backup Complete Window C.5.3 Restore Your Last Backup To restore the last system backup

ECN-360A-D2550 Embedded System Page 112 Figure C-39: Restore System Backup Complete Window C.5.4 Manual To restore the last system backup, please f

ECN-360A-D2550 Embedded System Page 113 C.6 Restore Systems from a Linux Server through LAN The One Key Recovery allows a client system to automat

ECN-360A-D2550 Embedded System Page 114 C.6.1 Configure DHCP Server Settings Step 1: Install the DHCP #yum install dhcp (CentOS, commands marked in

ECN-360A-D2550 Embedded System Page 115 filename “pxelinux.0”; C.6.2 Configure TFTP Settings Step 1: Install the tftp, httpd and syslinux. #yum i

ECN-360A-D2550 Embedded System Page 116 Debian Replace the TFTP settings from “inetd” to “xinetd” and annotate the “inetd” by adding “#”. #vi /etc

ECN-360A-D2550 Embedded System Page 117 C.6.4 Start the DHCP, TFTP and HTTP Start the DHCP, TFTP and HTTP. For example: #service xinetd restart Cent

ECN-360A-D2550 Embedded System Page 118 Modify: [image] comment = One Key Recovery path = /share/image browseable = yes writable = yes pub

ECN-360A-D2550 Embedded System Page 2 1.1 Overview Figure 1-1: ECN-360A-D2550 The ECN-360A-D2550 embedded system is a fanless system with two VGA p

ECN-360A-D2550 Embedded System Page 119 Step 2: Continue to configure the Boot Option Priorities BIOS option of the client system: Boot Option #1 

ECN-360A-D2550 Embedded System Page 120 NOTE: A firewall or a SELinux is not in use in the whole setup process. If there is a firewall or a SEL

ECN-360A-D2550 Embedded System Page 121 C.7 Other Information C.7.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHC

ECN-360A-D2550 Embedded System Page 122 Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Step 6:

ECN-360A-D2550 Embedded System Page 123 Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu. Continue to fo

ECN-360A-D2550 Embedded System Page 124 D Watchdog Timer Appendix D

ECN-360A-D2550 Embedded System Page 125 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI webs

ECN-360A-D2550 Embedded System Page 126 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. E

ECN-360A-D2550 Embedded System Page 127 Appendix E E Hazardous Materials Dis clos ure

ECN-360A-D2550 Embedded System Page 128 E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Witho

ECN-360A-D2550 Embedded System Page 3 1.4 Technical Specifications The ECN-360A-D2550 technical specifications are listed in Table 1-1. Chassis Colo

ECN-360A-D2550 Embedded System Page 129 Part Name Toxic or Hazardous Substances and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromiu

ECN-360A-D2550 Embedded System Page 130 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本

ECN-360A-D2550 Embedded System Page 4 P CIe Min i 1 x Full size (support mSATA) 1 x Half size Power Power Input 9~28V DC Power 1 : DC Jack Power

ECN-360A-D2550 Embedded System Page 5 Figure 1-2: ECN-360A-D2550 Front Panel 1.6 Rear Panel The rear panel of the ECN-360A-D2550 has the following

ECN-360A-D2550 Embedded System Page 6 Figure 1-3: ECN-360A-D2550 Rear Panel

ECN-360A-D2550 Embedded System Page 7 1.7 Dimensions The physical dimensions are shown below: Figure 1-4: Physical Dimensions (mm)

ECN-360A-D2550 Embedded System Page 8 Chapter 2 2 Unpacking

ECN-360A-D2550 Embedded System Page ii Revis ion Date Version Changes 1 July 2013 1.00 Initial release

ECN-360A-D2550 Embedded System Page 9 2.1 Anti-static Precautions WARNING: Failure to take ESD precautions during installation may result in perma

ECN-360A-D2550 Embedded System Page 10 2.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do

ECN-360A-D2550 Embedded System Page 11 Quantity Item and Part Number Im a g e 1 Utility CD 1 One Key Recovery CD Table 2-1: Package List Cont

ECN-360A-D2550 Embedded System Page 12 Chapter 3 3 Ins tallation

ECN-360A-D2550 Embedded System Page 13 3.1 Installation Precautions During installation, be aware of the precautions below:  Read the user manual:

ECN-360A-D2550 Embedded System Page 14 Step 1: Remove six retention screws from the bottom panel (Figure 3-1). Figure 3-1: Retention Screws Remova

ECN-360A-D2550 Embedded System Page 15 Step 3: Attach the HDD to the HDD bracket, and then slide the HDD to connect the HDD to the SATA connector.

ECN-360A-D2550 Embedded System Page 16 Figure 3-4: Wi-Fi Antenna Installation 3.5 Mo u nt the System To mount the embedded system onto a wall or so

ECN-360A-D2550 Embedded System Page 17 Step 5: Align the mounting holes in the sides of the mounting brackets with the predrilled holes in the moun

ECN-360A-D2550 Embedded System Page 18 Step 2: Plug the audio plug into the audio jack. Plug the audio plug into the audio jack. If the plug on you

ECN-360A-D2550 Embedded System Page iii Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in ord

ECN-360A-D2550 Embedded System Page 19 Figure 3-7: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LA

ECN-360A-D2550 Embedded System Page 20 Figure 3-8: DB-9 Serial Port Connector Step 3: Secure the connector. Secure the serial device connector to

ECN-360A-D2550 Embedded System Page 21 Figure 3-9: USB Device Connection Step 3: Insert the device connector. Once aligned, gently insert the USB

ECN-360A-D2550 Embedded System Page 22 Figure 3-10: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monito

ECN-360A-D2550 Embedded System Page 23 Chapter 4 4 System Motherboard

ECN-360A-D2550 Embedded System Page 24 4.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 4.1.1 Layout The fig

ECN-360A-D2550 Embedded System Page 25 Connector Type Label Backlight inverter connector 5-pin wafer INV1 Battery connector 2-pin wafer CN1 Di

ECN-360A-D2550 Embedded System Page 26 4.2 Internal Peripheral Connectors The section describes all of the connectors on the motherboard. 4.2.1 5 V

ECN-360A-D2550 Embedded System Page 27 The 10-pin audio connector is connected to external audio devices including speakers and microphones for the

ECN-360A-D2550 Embedded System Page 28 Figure 4-4: Backlight Inverter Connector Location Pin Description 1 LCD_BKLTCTL 2 GROUND 3 +12V 4 GROUND 5

ECN-360A-D2550 Embedded System Page iv Ta b le of Contents 1 INTRODUCTION ...

ECN-360A-D2550 Embedded System Page 29 Figure 4-5: Battery Connector Location Pin Description 1 Battery+ 2 GND Table 4-6: Battery Connector Pin

ECN-360A-D2550 Embedded System Page 30 Pin Description Pin Description 3 Output 3 4 Output 2 5 Output 1 6 Output 0 7 Input 3 8 Input 2 9

ECN-360A-D2550 Embedded System Page 31 4.2.7 Front Panel Connector CN Label: F_P ANEL1 CN Type: 10-pin header CN Location: See Figure 4-8 CN Pinou

ECN-360A-D2550 Embedded System Page 32 The keyboard and mouse connector can be connected to a standard PS/2 cable or PS/2 Y-cable to add keyboard an

ECN-360A-D2550 Embedded System Page 33 Figure 4-10: LVDS1 Connector Location Pin Description Pin Description 1 GND 2 GND 3 LVDS_DATA0 4 L

ECN-360A-D2550 Embedded System Page 34 NOTE: The M_PCIE1 slot supports mSATA devices. However, the SATA1 connector will be disabled when an mSAT

ECN-360A-D2550 Embedded System Page 35 Pin Description Pin Description 29 GND 30 SMBCLK 31 PCIE_TXN 32 SMBDATA 33 PCIE_TXP 34 GND 35 GN

ECN-360A-D2550 Embedded System Page 36 Pin Description Pin Description 1 GND 2 GND 3 PWR 4 PWR Table 4-13: Power Connector Pinouts 4.2.12

ECN-360A-D2550 Embedded System Page 37 4.2.13 RS-422/485 Serial Port Connector CN Label: COM4 CN Type: 4-pin wafer CN Location: See Figure 4-14 CN

ECN-360A-D2550 Embedded System Page 38 NOTE: The SATA1 connector will be disabled when an mSATA device is installed to the M_PCIE1 slot. Figur

ECN-360A-D2550 Embedded System Page v 4.1.3 External Interface Panel Connectors ... 25

ECN-360A-D2550 Embedded System Page 39 Figure 4-16: SO-DIMM Connector Location 4.2.16 USB Connector CN Label: USB4 CN Type: 8-pin header CN Locati

ECN-360A-D2550 Embedded System Page 40 4.3 External Peripheral Interface Connector Panel The figure below shows the external periphe4ral interface c

ECN-360A-D2550 Embedded System Page 41 Figure 4-19: RJ-45 Ethernet Connector LED Description LED Description A on: linked blinking: data is be

ECN-360A-D2550 Embedded System Page 42 4.3.3 VGA Connectors CN Label: VGA1, VGA2 CN Type: 15-pin Female CN Location: See Figure 4-18 CN Pinouts:

ECN-360A-D2550 Embedded System Page 43 4.4 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of t

ECN-360A-D2550 Embedded System Page 44 Setting Description Off Use AT power Table 4-23: AT/ATX Power Selection Jumper Settings Figure 4-21: AT/A

ECN-360A-D2550 Embedded System Page 45 Figure 4-22: Clear CMOS Jumper Location 4.4.3 LVDS 1 Voltage Selection WARNING: Permanent damage to the sc

ECN-360A-D2550 Embedded System Page 46 Figure 4-23: LVDS1 Voltage Selection Jumper Location 4.4.4 m S ATA/P CIe Min i Selection Jumper Label: MSA

ECN-360A-D2550 Embedded System Page 47 Chapter 5 5 BIOS

ECN-360A-D2550 Embedded System Page 48 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain

ECN-360A-D2550 Embedded System Page vi 5.2 MAIN ...

ECN-360A-D2550 Embedded System Page 49 Key Function Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page

ECN-360A-D2550 Embedded System Page 50 5.2 Ma in The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu giv

ECN-360A-D2550 Embedded System Page 51  System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minute

ECN-360A-D2550 Embedded System Page 52 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced ACPI Settings ACPI Slee

ECN-360A-D2550 Embedded System Page 53 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Advanced Wake system with Fixed Ti

ECN-360A-D2550 Embedded System Page 54 5.3.3 CPU Configuration Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and

ECN-360A-D2550 Embedded System Page 55  Hyper-Threading [Enabled] Use the Hyper-Threading BIOS option to enable or disable the Intel Hyper-Thread

ECN-360A-D2550 Embedded System Page 56 5.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information an

ECN-360A-D2550 Embedded System Page 57  Enabled DEFAULT Legacy USB support enabled  Auto Legacy USB support disabled if no USB devices are conn

ECN-360A-D2550 Embedded System Page 58 5.3.6.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 9) to configure the s

ECN-360A-D2550 Embedded System Page vii C.2 SETUP PROCEDURE FOR WINDOWS ...

ECN-360A-D2550 Embedded System Page 59  IO=2F8h; IRQ=3, 4 Serial Port I/O port address is 2F8h and the interrupt address is IRQ3, 4  IO=3E8h; IRQ

ECN-360A-D2550 Embedded System Page 60 5.3.6.1.3 Serial Port 3 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disabl

ECN-360A-D2550 Embedded System Page 61 5.3.6.1.4 Serial Port 4 Configuration  Serial Port [Enabled] Use the Serial Port option to enable or disabl

ECN-360A-D2550 Embedded System Page 62 5.3.7 F81866 H/W Monitor The F81866 H/W Monitor menu (BIOS Menu 10) contains the fan configuration submen

ECN-360A-D2550 Embedded System Page 63 o VSB3V o VBAT 5.3.7.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS

ECN-360A-D2550 Embedded System Page 64 5.3.8 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 12) allows the c

ECN-360A-D2550 Embedded System Page 65  Bits per second [115200] Use the Bits per second option to specify the serial port transmission speed. The

ECN-360A-D2550 Embedded System Page 66  Stop Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a se

ECN-360A-D2550 Embedded System Page 67 5.4 Chips et Use the Chipset menu (BIOS Menu 14) to access the Host Bridge and Southbridge configuration me

ECN-360A-D2550 Embedded System Page 68 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Chipset > Intel IGD Configuration

ECN-360A-D2550 Embedded System Page viii Lis t of Figures Figure 1-1: ECN-360A-D2550 ...

ECN-360A-D2550 Embedded System Page 69  IGFX - Boot Typ e [VBIOS Default] Use the IGFX - Boot Type option to select the display device used by th

ECN-360A-D2550 Embedded System Page 70 5.4.2 South Bridge Configuration Use the South Bridge Configuration menu (BIOS Menu 17) to configure the So

ECN-360A-D2550 Embedded System Page 71  Set Spread Spectrum Function [Dis abled] The Set Spread Spectrum Function option can help to improve CPU E

ECN-360A-D2550 Embedded System Page 72  Off Does not enable the keyboard Number Lock automatically. To use the 10-keys on the keyboard, press the

ECN-360A-D2550 Embedded System Page 73 5.6 Security Use the Security menu (BIOS Menu 19) to set system and user passwords. Aptio Setup Utility – Cop

ECN-360A-D2550 Embedded System Page 74 Aptio Setup Utility – Copyright (C) 2011 American Megatrends, Inc. Main Advanced Chipset Boot Security Save &

ECN-360A-D2550 Embedded System Page 75 A Safety Precautions Appendix A

ECN-360A-D2550 Embedded System Page 76 WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these pre

ECN-360A-D2550 Embedded System Page 77 A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the ECN-3

ECN-360A-D2550 Embedded System Page 78 A.1.3 Product Disposal CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certi

ECN-360A-D2550 Embedded System Page ix Figure 4-17: USB Connector Location ...

ECN-360A-D2550 Embedded System Page 79  The interior of the ECN-360A-D2550X does not require cleaning. Keep fluids away from the ECN-360A-D2550 in

ECN-360A-D2550 Embedded System Page 80 B BIOS Me n u Options Appendix B

ECN-360A-D2550 Embedded System Page 81  System Overview ...

ECN-360A-D2550 Embedded System Page 82  Bootup NumLock State [On] ...

ECN-360A-D2550 Embedded System Page 83 Appendix C C One Key Recovery

ECN-360A-D2550 Embedded System Page 84 C.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost s

ECN-360A-D2550 Embedded System Page 85 After completing the five initial setup procedures as described above, users can access the recovery tool by

ECN-360A-D2550 Embedded System Page 86 partitions. Please take the following table as a reference when calculating the size of the partition. OS

ECN-360A-D2550 Embedded System Page 87 o Ubuntu 8.10 (Intrepid) o Ubuntu 7.10 (Gutsy) o Ubuntu 6.10 (Edgy) o Debian 5.0 (Lenny) o Debian 4.0 (E

ECN-360A-D2550 Embedded System Page 88 C.2.1 Hardware and BIOS Setup Step 1: Make sure the system is powered off and unplugged. Step 2: Install a