Iei-integration NANO-945GSE2 User Manual

NANO-945GSE2 Page iIEI Technology Corp. User Manual NANO-945GSE2 MODEL: NANO-945GSE2 EPIC Single Board Computer with Intel® Atom™ Processor, VGA/LCD

NANO-945GSE2Page x Figure 3-26: Reset Button Connector Locations...40 Figure 3-2

NANO-945GSE2Page 86 BIOS Menu 7: Hardware Health Configuration  CPU FAN Mode Setting [Full On Mode] Use the CPU FAN Mode Setting option to config

NANO-945GSE2 Page 87 CPU Temp. Limit of OFF [000] WARNING: Setting this value too high may cause the fan to stop when the CPU is at a high temper

NANO-945GSE2Page 88  CPU Fan Start PWM [070] The Fan 3 Start PWM option can only be set if the CPU FAN Mode Setting option is set to Automatic Mod

NANO-945GSE2 Page 89o CPU Core o +1.05V o +3.30V o +12.0 V o +1.5V o +1.8V o 5VSB o VBAT 5.3.5 Power Configuration Use the Power Configurati

NANO-945GSE2Page 90 BIOS Menu 9: Advanced Power Configuration 5.3.5.1 APM Configuration The APM Configuration menu (784HBIOS Menu 10) allows the ad

NANO-945GSE2 Page 91 Power Off The system remains turned off  Power On The system turns on  Last State DEFAULT The system returns to its pre

NANO-945GSE2Page 92 Use the Resume PCI-Express WAKE# BIOS option to enable activity on the PCI-Express WAKE# signal to rouse the system from a suspe

NANO-945GSE2 Page 93BIOS Menu 11: Remote Access Configuration [Advanced]  Remote Access [Disabled] Use the Remote Access option to enable or disab

NANO-945GSE2Page 94 Use the Serial Port Number option to select the serial port to use for remote access.  COM1 DEFAULT System is remotely accessed

NANO-945GSE2 Page 95 Redirection After BIOS POST [Always] Use the Redirection After BIOS POST option to specify when console redirection should oc

NANO-945GSE2 Page xiFigure 6-10: VGA Driver Setup Files Extracted ... 117 Figure

NANO-945GSE2Page 96 Use the Sredir Memory Display Delay option to select the delay before memory information is displayed. Configuration options are

NANO-945GSE2 Page 97 Disabled USB function disabled  Enabled DEFAULT USB function enabled  USB2.0 Controller Mode [HiSpeed] The USB2.0 Controll

NANO-945GSE2Page 98 menu may cause the system to malfunction. BIOS Menu 13: PCI/PnP Configuration  IRQ# [Available] Use the IRQ# address to spec

NANO-945GSE2 Page 99 IRQ 15  DMA Channel# [Available] Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP device

NANO-945GSE2Page 100 BIOS Menu 14: Boot 5.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (886H789HBIOS Menu 14) to configu

NANO-945GSE2 Page 101 Disabled No POST procedures are skipped  Enabled DEFAULT Some POST procedures are skipped to decrease the system boot time

NANO-945GSE2Page 102 Lock LED light on the keyboard is lit.  Boot From LAN Support [Disabled] The BOOT From LAN Support option enables the system

NANO-945GSE2 Page 103BIOS Menu 17: Security  Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password.

NANO-945GSE2Page 104 menu may cause the system to malfunction. BIOS Menu 18: Chipset 5.7.1 Northbridge Chipset Configuration Use the Northbridge C

NANO-945GSE2 Page 105The Memory Hole reserves the memory space between 15MB and 16MB for ISA expansion cards that require a specified area of memor

NANO-945GSE2Page xii List of Tables Table 1-1: Technical Specifications...

NANO-945GSE2Page 106 Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can be allocated as graphics memory. This option

NANO-945GSE2 Page 107 BIOS Menu 20:Southbridge Chipset Configuration  Audio Controller [All Disabled] The Audio Controller option enables or disab

NANO-945GSE2Page 108 BIOS Menu 21:Exit  Save Changes and Exit Use the Save Changes and Exit option to save the changes made to the BIOS optio

NANO-945GSE2 Page 109Chapter 6 6 Software Drivers

NANO-945GSE2Page 110 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is subject to

NANO-945GSE2 Page 111Step 2: The screen in 802HFigure 6-1 appears. Figure 6-1: Start Up Screen Step 3: Click NANO-945GSE2. Step 4: The screen in

NANO-945GSE2Page 112 Step 6: The list of drivers in 804HFigure 6-3 appears.Step 0: Figure 6-3: Drivers 6.3 Chipset Driver Installation To install

NANO-945GSE2 Page 113Figure 6-4: Chipset Driver Welcome Screen Step 4: Click Next to continue. Step 5: The license agreement in 808HFigure 6-5 app

NANO-945GSE2Page 114 Step 7: Click the YES button to accept the license agreement and continue. Step 8: The Read Me file in 809HFigure 6-6 appears

NANO-945GSE2 Page 115Figure 6-7: Chipset Driver Setup Operations Step 11: Once the Setup Operations are complete, click the NEXT icon to continue. S

NANO-945GSE2 Page xiiiTable 4-2: AT Power Select Jumper Settings ...49 Tabl

NANO-945GSE2Page 116 Step 13: Select “Yes, I want to restart the computer now” and click the Finish icon. See 811HFigure 6-8.Step 0: 6.4 VGA Driver

NANO-945GSE2 Page 117Figure 6-10: VGA Driver Setup Files Extracted Step 6: The Welcome Screen in 816HFigure 6-11 appears. Figure 6-11: VGA Driver W

NANO-945GSE2Page 118 Figure 6-12: VGA Driver License Agreement Step 9: Read the License Agreement. Step 10: Click YES to accept the license agreem

NANO-945GSE2 Page 119Step 12: Click NEXT to continue. Step 13: Setup Operations are performed as shown in 819HFigure 6-14. NOTE: The “Found New Har

NANO-945GSE2Page 120 Figure 6-15: VGA Driver Installation Finish Screen Step 16: Select “Yes, I want to restart the computer now” and click FINISH.

NANO-945GSE2 Page 121Figure 6-16: LAN Driver Welcome Screen Step 4: Click NEXT to continue. Step 5: The Ready to Install screen in 824HFigure 6-17

NANO-945GSE2Page 122 Step 8: The installation progress can be monitored in the progress bar shown in 825HFigure 6-18. Figure 6-18: LAN Driver Insta

NANO-945GSE2 Page 1236.6 Audio Driver Installation There is no audio driver on the NANO-945GSE2. To add audio capabilities to the NANO-945GSE2, conn

NANO-945GSE2Page 124 Step 3: Browse to “E:\4-Audio\ALC665\Windows\Windows 98Gold, 98se, Me, 2000, XP, 2003(32,64 bits)\A3.84” 830HFigure 6-21 Figur

NANO-945GSE2 Page 125Step 7: The Verification window in 833HFigure 6-23 may appear. Figure 6-23: AC’97 Driver Installation Verification Step 8: Cl

NANO-945GSE2Page xiv BIOS Menus Menu 1: Main...

NANO-945GSE2Page 126 Step 10: Select “Yes, I wish to restart my computer now” And click FINISH to exit the InstallShield Wizard and restart the comp

NANO-945GSE2 Page 127Figure 6-26: SATA RAID Driver Installation Program Step 5: Double-click the IATA85CD.exe program icon in 838HFigure 6-27. Figu

NANO-945GSE2Page 128 Figure 6-28: InstallShield Wizard Setup Screen Step 7: 840HFigure 6-29 shows the Matrix Storage Manager software configuring th

NANO-945GSE2 Page 129Figure 6-30: Matrix Storage Manager Welcome Screen Step 9: Click NEXT and a warning appears (842HFigure 6-31). Read the warnin

NANO-945GSE2Page 130 Figure 6-32: Matrix Storage Manager License Agreement Step 11: Read the license agreement. To accept the terms and conditions s

NANO-945GSE2 Page 131Step 13: After the driver installation process is complete, a confirmation screen appears (845HFigure 6-34). Figure 6-34: Matri

NANO-945GSE2Page 132 Figure 6-35: iSMM Directory Step 4: Double click the iSMM EN V1.11.00 directory icon. (849HFigure 6-35) Step 5: The contents

NANO-945GSE2 Page 133Step 7: The iSMM InstallShield Welcome Screen appears. (852HFigure 6-37) Figure 6-37: iSMM InstallShield Welcome Screen Step 8

NANO-945GSE2Page 134 Step 10: Select “I accept the terms of the license agreement.” (854HFigure 6-38) Step 11: Click NEXT to continue.(855HFigure 6-

NANO-945GSE2 Page 135Step 15: The Setup Type screen appears. (859HFigure 6-40) Figure 6-40: iSMM Setup Type Step 16: Select “Complete” (860HFigure 6

NANO-945GSE2 Page 1Chapter 1 1 Introduction

NANO-945GSE2Page 136 Step 18: The Installation Confirmation screen appears. (862HFigure 6-41) Figure 6-41: iSMM Installation Confirmation Step 19: C

NANO-945GSE2 Page 137Step 20: The InstallShield Wizard Completed appears when the drivers are finished installing. (864HFigure 6-42) Figure 6-42: iS

NANO-945GSE2Page 138 Appendix A A BIOS Options

NANO-945GSE2 Page 139Below is a list of BIOS configuration options in the BIOS chapter. 295H　 System Overview ...

NANO-945GSE2Page 140 328H　 Serial Port Mode...

NANO-945GSE2 Page 141363H　 Save Changes and Exit ...

NANO-945GSE2Page 142 Appendix B B Terminology

NANO-945GSE2 Page 143AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Int

NANO-945GSE2Page 144 DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the

NANO-945GSE2 Page 145LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid cryst

NANO-945GSE2Page 2 1.1 Overview Figure 1-1: NANO-945GSE2 1.1.1 NANO-945GSE2 Introduction The NANO-945GSE2 EPIC motherboards are embedded 45 nm Inte

NANO-945GSE2Page 146 Appendix C C Digital I/O Interface

NANO-945GSE2 Page 147C.1 Introduction The DIO connector on the NANO-945GSE2 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4

NANO-945GSE2Page 148 C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital I/O. An

NANO-945GSE2 Page 149Appendix D D Watchdog Timer

NANO-945GSE2Page 150 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific dr

NANO-945GSE2 Page 151 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; IN

NANO-945GSE2Page 152 Appendix E E Compatibility

NANO-945GSE2 Page 153 NOTE: The compatible items described here have been tested by the IEI R&D team and found to be compatible with the NANO-94

NANO-945GSE2Page 154 E.3 Compatible Memory Modules NOTE: The memory modules listed below have been tested on the NANO-945GSE2 other memory modules

NANO-945GSE2 Page 155Appendix F F Hazardous Materials Disclosure

NANO-945GSE2 Page 3 Figure 1-2: NANO-945GSE2 Overview

NANO-945GSE2Page 156 F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The deta

NANO-945GSE2 Page 157Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(CR(VI)) Polybromina

NANO-945GSE2Page 158 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的

NANO-945GSE2Page 4 1.2.1 Dimensions The dimensions of the board are listed below:  Length: 165 mm  Width: 115 mm Figure 1-3: NANO-945GSE2 Dime

NANO-945GSE2 Page 51.2.3 Data Flow 6Figure 1-5 shows the data flow between the two on-board chipsets and other components installed on the motherboa

NANO-945GSE2Page ii Revision Date Version Changes 17 April, 2009 1.00 Initial release

NANO-945GSE2Page 6 1.2.4 Technical Specifications NANO-945GSE2 technical specifications are listed below. Specification/Model NANO-945GSE2 Form Fac

NANO-945GSE2 Page 7Specification/Model NANO-945GSE2 Keyboard/Mouse One PS/2 port LPT One internal parallel port connector Serial Ports Three RS-232

NANO-945GSE2Page 8 Chapter 2 2 Unpacking

NANO-945GSE2 Page 92.1 Anti-static Precautions WARNING! Failure to take ESD precautions during the installation of the NANO-945GSE2 may result in p

NANO-945GSE2Page 10 2.3 Unpacking Checklist NOTE: If any of the components listed in the checklist below are missing, do not proceed with the insta

NANO-945GSE2 Page 111 Utility CD 1 Quick Installation Guide 2.3.2 Optional Items The following components are optional: Item and Part Number Ima

NANO-945GSE2Page 12 Chapter 3 3 Connector Pinouts

NANO-945GSE2 Page 133.1 Peripheral Interface Connectors 6Figure 3-1 shows the on-board peripheral connectors, rear panel peripheral connectors and o

NANO-945GSE2Page 14 3.2 Peripheral Interface Connectors 6Table 3-1 shows a list of the peripheral interface connectors on the NANO-945GSE2. Detailed

NANO-945GSE2 Page 15Serial port connector (RS-232/422/485) 14-pin header COM3 TTL LCD interface connector 40-pin crimp CN3 USB 2.0 connector 8-pin

NANO-945GSE2 Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve relia

NANO-945GSE2Page 16 The 5V Power Connector provides +5V power output. Figure 3-3: PS ON and +5V Standby Power Connector Pinouts PIN NO. DESCRIPTIO

NANO-945GSE2 Page 17Figure 3-4: AT Power Connector Location PIN NO. DESCRIPTION 1 GND 2 GND 3 +12V 4 +12V Table 3-4: AT Power Connector Pinouts 3.

NANO-945GSE2Page 18 Figure 3-5: Audio Connector Location (9-pin) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 LINEOUTR 2 LIR 3 GND 4 GND 5 LINEOUT

NANO-945GSE2 Page 19 Figure 3-6: Panel Backlight Connector Pinout Locations PIN NO. DESCRIPTION 1 LCD Backlight Control 2 GROUND 3 +12V 4 GROUND 5

NANO-945GSE2Page 20 Figure 3-7: Battery Connector Location PIN NO. DESCRIPTION 1 Battery+ 2 Ground Table 3-7: Battery Connector Pinouts 3.3.6 Co

NANO-945GSE2 Page 21 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GROUND 26 VCC-IN CHECK1 2 DATA 3 27 DATA 11 3 DATA 4 28 DATA 12 4 DATA 5 2

NANO-945GSE2Page 22 3.3.7 Digital Input/Output (DIO) Connector CN Label: DIO1 CN Type: 10-pin header (2x5) CN Location: See Figure 3-9 CN Pinouts:

NANO-945GSE2 Page 23The cooling fan connector provides a 12V, 500mA current to the cooling fan. The connector has a "rotation" pin to get

NANO-945GSE2Page 24  Power button  Reset  Power LED  HDD LED Figure 3-11: Front Panel Connector Pinout Locations (8-pin) FUNCTION PIN DESCRIP

NANO-945GSE2 Page 25Figure 3-12: Infrared Connector Pinout Locations PIN NO. DESCRIPTION 1 VCC 2 NC 3 IR-RX 4 GND 5 IR-TX Table 3-12: Infrared Con

NANO-945GSE2Page iv Table of Contents 1 INTRODUCTION...

NANO-945GSE2Page 26 Figure 3-13: LVDS LCD Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GND1 2 GND2 3 A_Y0 4 A_Y0# 5 A_

NANO-945GSE2 Page 273.3.12 Parallel Port Connector CN Label: J3 CN Type: 26-pin header CN Location: See Figure 3-14 CN Pinouts: See Table 3-14 The

NANO-945GSE2Page 28 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 12 PAPER EMPTY 25 GROUND 13 PRINTER SELECT 26 NC Table 3-14: Parallel Port Connector

NANO-945GSE2 Page 29Pin No. Column A Column B Column C Column D 4 C/BE0# AD07 GND AD06 5 GND AD09 AD08 GND 6 AD11 VI/O2 AD10 M66EN 7 AD14 AD13

NANO-945GSE2Page 30 3.3.14 PC/104 Connector CN Label: J6 CN Type: 104-pin PC/104 slot CN Location: See 6Figure 3-16 CN Pinouts: See Table 3-16 an

NANO-945GSE2 Page 31PIN Description PIN Description PIN Description PIN Description A11 AEN A27 SA4 B11 -SMEMW B27 TC A12 SA19 A28 SA3 B

NANO-945GSE2Page 32 Figure 3-17: SATA Drive Connector Locations PIN NO. DESCRIPTION 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 3-18: SATA Driv

NANO-945GSE2 Page 33 Figure 3-18: SATA Power Connector Locations Pin No. Description 1 +5V 2 GND Table 3-19: SATA Power Connector Pinouts 3.3.17

NANO-945GSE2Page 34 Figure 3-19: COM2 and COM4 Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 Data Carrier Direct (DCD)

NANO-945GSE2 Page 35Figure 3-20: COM3 Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DATA CARRIER DETECT (DCD) 2 DATA SET

NANO-945GSE2 Page v3.3.11 LVDS LCD Connector... 25 3.3.12 Parallel

NANO-945GSE2Page 36 Figure 3-21: LCD TTL Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC_LCD 2 VCC_LCD 3 GND 4 GN

NANO-945GSE2 Page 373.3.20 USB Connectors (Internal) CN Label: USB2 and USB3 CN Type: 8-pin header (2x4) CN Location: See 7Figure 3-22 CN Pinouts:

NANO-945GSE2Page 38  1 x Keyboard/mouse connector  2 x LAN connectors  1 x Serial port connector  1 x VGA connector  2 x USB connectors

NANO-945GSE2 Page 39PIN DESCRIPTION 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK 6 MS CLOCK Table 3-24: Keyboard Connector Pinouts 3.4.2 LAN Connector

NANO-945GSE2Page 40 3.4.3 Reset Button The reset button enables users to reboot the system when the system is turned on. Figure 3-26: Reset Button L

NANO-945GSE2 Page 41 Figure 3-27: COM1 Pinout Locations3.4.5 USB Connectors CN Label: USB1 CN Type: Dual USB port CN Location: See 7Figure 3-23 CN

NANO-945GSE2Page 42 Figure 3-28: VGA Connector PIN DESCRIPTION PIN DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 CRT_PLUG- 7 GND 8 GND 9 VCC 1

NANO-945GSE2 Page 43Chapter 4 4 Installation

NANO-945GSE2Page 44 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the NANO-945GSE2 may result in

NANO-945GSE2 Page 454.2.1 Installation Notices WARNING: The installation instructions described in this manual should be carefully followed in orde

NANO-945GSE2Page vi 4.7.1 AT Power Connection ... 56 4.7.2 PC/104

NANO-945GSE2Page 46 4.3 SO-DIMM Installation WARNING: Using incorrectly specified SO-DIMM may cause permanently damage the NANO-945GSE2. Please mak

NANO-945GSE2 Page 47Step 5: Secure the SO-DIMM. Release the arms on the SO-DIMM socket. They clip into place and secure the SO-DIMM in the socket.S

NANO-945GSE2Page 48 4.5 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal p

NANO-945GSE2 Page 49Jumper Label: ATXCTL1 Jumper Type: 2-pin header Jumper Settings: See Table 4-2 Jumper Location: See Figure 4-3 The AT Power Sel

NANO-945GSE2Page 50 4.5.2 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header Jumper Settings: See 7Table 4-3 Jumper Location: See 7Fi

NANO-945GSE2 Page 51Figure 4-4: Clear CMOS Jumper 4.5.3 COM3 Function Select Jumper Jumper Label: JP1 Jumper Type: 6-pin header Jumper Settings: Se

NANO-945GSE2Page 52 Figure 4-5: COM 2 Function Select Jumper Location4.5.4 LVDS1 Panel Resolution Jumper Jumper Label: J_LCD_TYPE1 Jumper Type: 8-

NANO-945GSE2 Page 53 Figure 4-6:LVDS Panel Resolution Jumper Pinout Locations4.5.5 LVDS Voltage Selection WARNING: Permanent damage to the screen a

NANO-945GSE2Page 54 The LVDS Voltage Selection jumper location is shown in Figure 4-7. Figure 4-7: LVDS Voltage Selection Jumper Pinout Locations4.

NANO-945GSE2 Page 55 Figure 4-8:COM2 Function Select Jumper Location4.6 Chassis Installation 4.6.1 Airflow WARNING: Airflow is critical to the cool

NANO-945GSE2 Page vii5.5.2 Boot Device Priority ... 102 5.6 SECUR

NANO-945GSE2Page 56 [email protected] or visit the IEI website (2http://www.ieiworld.com.tw) to find out more about the available chassis. 4.6.2 Mot

NANO-945GSE2 Page 57 WARNING: Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the NANO-945GSE2. S

NANO-945GSE2Page 58 Figure 4-10: Connect Power Cable to Power Supply4.7.2 PC/104-Plus Card Installation To install a PC/104-Plus card, please refer

NANO-945GSE2 Page 59Step 1: Align the connectors. Make sure that the connectors are lined up correctly. The connectors should match up with the slo

NANO-945GSE2Page 60 Figure 4-12: SATA Drive Cable ConnectionStep 3: Connect the cable to the SATA disk. Connect the connector on the other end of

NANO-945GSE2 Page 61 Figure 4-13: SATA Power Drive Connection4.7.4 Single RS-232 Cable (w/o Bracket) The single RS-232 cable consists of one serial

NANO-945GSE2Page 62 Figure 4-14: Single RS-232 Cable Installation Step 4: Secure the bracket. The single RS-232 connector has two retention screws

NANO-945GSE2 Page 63each cable connector with pin 1 on the NANO-945GSE2 USB connector. Step 3: Insert the cable connectors. Once the cable connecto

NANO-945GSE2Page 64 Step 3: Insert the cable connectors. Once the cable connector is properly aligned with the 26-pin box-header connector on the N

NANO-945GSE2 Page 65Figure 4-17: Connect the LPT Device 4.7.7 Dual RS-422/485 Cable An optional RS-422/485 dual serial port connector cable is avail

NANO-945GSE2Page viii ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ... 156

NANO-945GSE2Page 66 Figure 4-18: Dual Serial Port Connector Cable ConnectionStep 4: Attach DB-9 serial port connectors to the chassis. The dual DB-

NANO-945GSE2 Page 674.8.1 LAN Connection (Single Connector) There are two external RJ-45 LAN connectors. The RJ-45 connectors enable connection to

NANO-945GSE2Page 68 mouse to the system. Follow the steps below to connect a keyboard and mouse to the NANO-945GSE2. Step 1: Locate the dual PS/2 c

NANO-945GSE2 Page 69Step 1: Locate the DB-9 connector. The location of the DB-9 connector is shown in Chapter 3. Step 2: Insert the serial connect

NANO-945GSE2Page 70 Figure 4-22: USB Connector 4.8.5 VGA Monitor Connection The NANO-945GSE2 has a single female DB-15 connector on the external per

NANO-945GSE2 Page 71Figure 4-23: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external in

NANO-945GSE2Page 72 Chapter 5 5 BIOS Screens

NANO-945GSE2 Page 735.1 Introduction A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allows users to modify t

NANO-945GSE2Page 74 F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 /F3 key Change color from total 16 colors.

NANO-945GSE2 Page 755.2 Main The Main BIOS menu (7BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of th

NANO-945GSE2 Page ixList of Figures Figure 1-1: NANO-945GSE2...

NANO-945GSE2Page 76 Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.  System Date [xx/xx/xx] Use

NANO-945GSE2 Page 77BIOS Menu 2: Advanced 5.3.1 CPU Configuration Use the CPU Configuration menu (873H775HBIOS Menu 3) to view detailed CPU specific

NANO-945GSE2Page 78  Frequency: Lists the CPU processing speed  FSB Speed: Lists the FSB speed  Cache L1: Lists the CPU L1 cache size  Cache

NANO-945GSE2 Page 79storage devices. Some legacy OS do not support this mode.  Legacy IDE Channels [PATA Pri, SATA Sec]  SATA Only Only the SAT

NANO-945GSE2Page 80 BIOS Menu 5: IDE Master and IDE Slave Configuration  Auto-Detected Drive Parameters The “grayed-out” items in the left frame

NANO-945GSE2 Page 81 32Bit Data Transfer: Enables 32-bit data transfer.  Type [Auto] Use the Type BIOS option select the type of device the AMIB

NANO-945GSE2Page 82  Block (Multi Sector Transfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the de

NANO-945GSE2 Page 83 Auto DEFAULT BIOS auto detects the DMA mode. Use this value if the IDE disk drive support cannot be determined.  SWDMA0 Sin

NANO-945GSE2Page 84 Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting Technology (SMART) on the driv

NANO-945GSE2 Page 85Use the Serial Port1 Address option to select the Serial Port 1 base address.  Disabled No base address is assigned to Seri