Page 1 PM-LX-800 CPU Card
List of BIOS Menus BIOS Menu 1: AwardBIOS CMOS Setup Utility ...80 BIOS Menu 2: Standard CMOS Fe
Page 100 IEI® Technology, Corp. HSYNC Polarity [Low] The HSYNC Polarity option can only be configured if the Flat Panel Type option is not set t
Page 101 PM-LX-800 CPU Card5.5 Integrated Peripherals Use the Integrated Peripherals menu (BIOS Menu 7) to change the configuration options for the
Page 102 IEI® Technology, Corp. Mode 1 PIO mode 1 selected with a maximum transfer rate of 5.2MBps. Mode 2 PIO mode 2 selected with a maxim
Page 103 PM-LX-800 CPU Card Enabled (Default) Block mode is supported. Onboard FDC Controller [Disabled] Use the Onboard FDC Controller optio
Page 104 IEI® Technology, Corp. Onboard Serial Port 3 [Disabled] Use the Onboard Serial Port 3 option to select the I/O address and IRQ for th
Page 105 PM-LX-800 CPU Card ECP The parallel port operates in the extended capabilities port (ECP) mode. The ECP mode supports bi-directional com
Page 106 IEI® Technology, Corp. 5.6 Power Management Setup Use the Power Management Setup menu (BIOS Menu 8) to set the BIOS power management and s
Page 107 PM-LX-800 CPU Card Power Management [APM] Use the Power Management option to set the power management type used by the system. Disabled
Page 108 IEI® Technology, Corp. x Suspend Mode [Disabled] The Suspend Mode option can only be selected if the Power Management option is set to
Page 109 PM-LX-800 CPU Card5.7 PnP/PCI Configurations Use the PnP/PCI Configurations menu (BIOS Menu 9) to set the plug and play, and PCI options. B
PM-LX-800 CPU CardGlossary AC ’97 Audio Codec 97 ACPI Advanced Configuration and Power Interface APM Advanced Power Management ARMD ATAPI Removab
Page 110 IEI® Technology, Corp. Disabled (Default) ESCD will not be reconfigured Enabled ESCD will be reconfigured after you exit setup R
Page 111 PM-LX-800 CPU Card x IRQ Resources [Press Enter] The IRQ Resources option (BIOS Menu 10) can only be selected if the Resources Controlled
Page 112 IEI® Technology, Corp. Reserved The IRQ is reserved by BIOS. x Memory Resources [Press Enter] The Memory Resources menu (BIOS Menu
Page 113 PM-LX-800 CPU Card Reserved Memory Base [N/A] The Reserved Memory Base option specifies the base address for the peripheral device. The R
Page 114 IEI® Technology, Corp. PCI/VGA Palette Snoop [Disabled] The PCI/VGA Palette Snoop option enables the system to determine whether or no
Page 115 PM-LX-800 CPU Card5.8 PC Health Status The PC Health Status menu (BIOS Menu 12) has two user configurable options and shows system operati
Page 116 IEI® Technology, Corp. CPU Warning Temperature Use the CPU Warning Temperature option to specify a CPU operating temperature threshold
Page 117 PM-LX-800 CPU CardChapter6 6 Software Drivers
Page 118 IEI® Technology, Corp. 6.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and i
Page 119 PM-LX-800 CPU Card Figure 6-1: AMD LX/GX CD Main Menu Step 2: A window appears listing the drivers available for installation (Figure 6-2)
Page 12 IEI® Technology, Corp. THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 120 IEI® Technology, Corp. Figure 6-2: AMD LX/GX CD Driver Menu Step 3: Select any item from the list to view more information on the driver
Page 121 PM-LX-800 CPU Card6.2 VGA Driver To install the VGA driver please follow the steps below. Step 1: Step 2: Open Windows Control Panel (Figur
Page 122 IEI® Technology, Corp. Figure 6-4: Double Click the System Icon Step 3: Step 4: Double click the Device Manager tab (Figure 6-5). Figure
Page 123 PM-LX-800 CPU CardFigure 6-6: Device Manager List Step 5: Expand the Display Adapters category (Figure 6-7). Right click the adapter and s
Page 124 IEI® Technology, Corp. Figure 6-7: Expand the Display Adapters Category Step 6: From the Driver tab of the Properties window, click Upda
Page 125 PM-LX-800 CPU Card Figure 6-8: Update Driver Step 7: The Upgrade Device Driver Wizard appears (Figure 6-9). Click NEXT to continue.
Page 126 IEI® Technology, Corp. Figure 6-9: Upgrade Device Driver Wizard Step 8: The Install Hardware Device Driver screen appears (Figure 6-10).
Page 127 PM-LX-800 CPU Card Figure 6-10: Search for Suitable Driver Step 9: Select Specify a Location in the Locate Driver Files window (Figure 6-1
Page 128 IEI® Technology, Corp. Figure 6-11: Locate Driver Files Step 10: Step 11: Click Browse and navigate to the X:\AMD\LX800\XP\VGA 2.01.05 di
Page 129 PM-LX-800 CPU CardStep 12: Step 1: Step 2: Step 3: Step 4: Step 5: Step 6: A driver files location menu window appears. Click NEXT to conti
Page 13 PM-LX-800 CPU Card1 Introduction Chapter1
Page 130 IEI® Technology, Corp. Figure 6-15: Install Wizard Welcome Screen Click NEXT to continue the installation or CANCEL to stop the installat
Page 131 PM-LX-800 CPU Card Figure 6-16: Installing Screen Click FINISH to complete the installation and exit the Install Shield Wizard. Step 10: St
Page 132 IEI® Technology, Corp. Figure 6-17: Restart the Computer
Page 133 PM-LX-800 CPU CardAppendix A A BIOS Configuration Options
Page 134 IEI® Technology, Corp. A.1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 5. Load Fail-Sa
Page 135 PM-LX-800 CPU Card Boot Up Floppy Seek [Disabled] ...91 Boot Up N
Page 136 IEI® Technology, Corp. Onboard Serial Port 2 [2F8/IRQ3]... 103 Onbo
Page 137 PM-LX-800 CPU CardAppendixB B Watchdog Timer
Page 138 IEI® Technology, Corp. NOTE: The following discussion applies to DOS environment. It is recommended you contact IEI support or visit our
Page 139 PM-LX-800 CPU Card NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system will reset. Example p
Page 14 IEI® Technology, Corp. 1.1 PM-LX-800 Motherboard Introduction The PC/104 form factor PM-LX-800 is a highly integrated embedded computer spe
Page 140 IEI® Technology, Corp. THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 141 PM-LX-800 CPU CardAppendixC C Address Mapping
Page 142 IEI® Technology, Corp. C.1 I/O Address Map I/O Address Range Description 000-01F DMA Controller 020-021 Interrupt Controller 040-043 Syst
Page 143 PM-LX-800 CPU CardC.3 IRQ Mapping Table IRQ# Description IRQ# Description IRQ0 System Timer IRQ8 RTC clock IRQ1 Keyboard IRQ9 ACPI IR
Page 144 IEI® Technology, Corp. THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 145 PM-LX-800 CPU Card D Index
Page 146 IEI® Technology, Corp. 2 24-bit TTL LCD... 14 A ACPI ... 106, 107 Ad
PM-LX-800 CPU CardM Mini jumper pack... 29, 68 O Onboard Jumpers ... 62 Operating Temperature ...
Page 15 PM-LX-800 CPU Card1.2 PM-LX-800 Motherboard Overview Figure 1-1: PM-LX-800 Motherboard Overview (Front Side) Figure 1-2: PM-LX-800 Motherb
Page 16 IEI® Technology, Corp. 1.2.1 PM-LX-800 Motherboard Connectors The PM-LX-800 motherboard has the following connectors on-board: 1 x AT 12
Page 17 PM-LX-800 CPU CardSPECIFICATION DESCRIPTION Display CRT integrated in AMD™ LX 800 TTL 24 bit TTL integrated in AMD LX 800 HDD Interface
Page 18 IEI® Technology, Corp. THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 19 PM-LX-800 CPU CardChapter2 2 Detailed Specifications
Page 2 IEI® Technology, Corp. REVISION HISTORY Title PM-LX-800 Motherboard Revision Number Description Date of Issue 1.0 Initial release Nove
Page 20 IEI® Technology, Corp. 2.1 CPU Support The PM-LX-800 has a preinstalled AMD LX 800 processor. Technical specifications for the AMD LX 800 p
Page 21 PM-LX-800 CPU Card2.2 System Chipset The PM-LX-800 motherboard has an AMD Geode™ CS5536 chipset installed. The AMD Geode™ CS5536 is a compan
Page 22 IEI® Technology, Corp. o LPC (Low Pin Count) Port o General Purpose I/Os (GPIOs) o 8 Multi-Function General Purpose Timers (MFGPTs)
Page 23 PM-LX-800 CPU Card2.2.1 Data Flow Figure 2-1 shows the data flow between the system chipset, the CPU and other I/O interfaces that can conne
Page 24 IEI® Technology, Corp. 2.3 Graphics Support Table 2-1 lists the PM-LX-800 graphics processor features. Feature AMD Geode™ LX Processor Col
Page 25 PM-LX-800 CPU Card2.4 Memory Support Up to 1GB of DDR 333 MHz SO-DIMM SDRAM is supported. 2.5 PCI Bus Interface Support The GeodeLink PCI So
Page 26 IEI® Technology, Corp. Provides PCI bus master data transfer Provides PCI memory space or I/O space mapped data transfer Suppo
Page 27 PM-LX-800 CPU Card2.10 System Monitoring The PM-LX-800 motherboard is capable of self-monitoring various aspects of its operating status inc
Page 28 IEI® Technology, Corp. 2.13 Power Consumption Table 2-2 shows the power consumption parameters for the PM-LX-800 when an AMD LX-800 CPU is
Page 29 PM-LX-800 CPU Card2.15 Packaged Contents and Optional Accessory Items 2.15.1 Package Contents When you unpack the PM-LX-800 motherboard, you
PM-LX-800 CPU CardTable of Contents 1 INTRODUCTION...
Page 30 IEI® Technology, Corp. THIS PAGE IS INTENTIONALLY LEFT BLANK
Page 31 PM-LX-800 CPU CardChapter3 3 Connectors and Jumpers
Page 32 IEI® Technology, Corp. 3.1 Peripheral Interface Connectors The locations of the peripheral interface connectors are shown in Section 3.1.1.
Page 33 PM-LX-800 CPU Card Figure 3-2: Connector and Jumper Locations (Solder Side) 3.1.2 Peripheral Interface Connectors Table 3-1 shows a list of
Page 34 IEI® Technology, Corp. Connector Type Label PCI-104 connector PCI-104 connector CN6A/B RS-232 Serial Communications connector 10-pin h
Page 35 PM-LX-800 CPU Card PIN DESCRIPTION 1 VCC12 2 GND 3 VCC5 Table 3-3: 12V / 5V Power Connector Pinouts Figure 3-3: 12V / 5V Power Connector
Page 36 IEI® Technology, Corp. The 12V input connector can be used to supply 12V power to the motherboard. PIN DESCRIPTION 1 N/C 2 GND 3 -12V Tabl
Page 37 PM-LX-800 CPU Card3.2.3 200-pin DDR SO-DIMM Socket CN Label: CN3 CN Type: 200-pin header CN Pinouts: See Table 3-5 CN Location: See Figure
Page 38 IEI® Technology, Corp. Pin Front Pin Back Pin Front Pin Back 47 DQS2 48 DM2\DQS11 147 DQS5 148 DM5\DQS14 49 DQ18 50 DQ22 149 V
Page 39 PM-LX-800 CPU Card Figure 3-5: 200-pin DDR SO-DIMM Socket Location 3.2.4 Battery Connector CN Label: BT1 CN Type: 2-pin header CN Pinouts:
Page 4 IEI® Technology, Corp. 3.1.3 Onboard Jumpers... 34
Page 40 IEI® Technology, Corp. WARNING! 1. Keep batteries away from children. 2. There is a danger of explosion if the battery is incorrectly
Page 41 PM-LX-800 CPU Card3.2.5 CompactFlash Connector CN Label: CN8 CN Type: 50-pin header (2x25 pins) CN Pinouts: See Table 3-7 CN Location: See
Page 42 IEI® Technology, Corp. PIN DESCRIPTION PIN DESCRIPTION 23 D02 48 DO9 24 (N/C) 49 D10 25 GROUND 50 GND Table 3-7: CompactFlash Connect
Page 43 PM-LX-800 CPU Card PIN DESCRIPTION PIN DESCRIPTION 1 RESET# 2 GND 3 DATA 7 4 DATA 8 5 DATA 6 6 DATA 9 7 DATA 5 8 DATA 10 9 DATA 4 1
Page 44 IEI® Technology, Corp. Figure 3-8: IDE Interface Connector Location 3.2.7 Inverter Connector CN Label: CN5 CN Type: 5-pin header CN Pin
Page 45 PM-LX-800 CPU Card PIN DESCRIPTION 1 LCD_BKLTCTL 2 GND 3 VCC12 4 GND 5 LCD_BKLEN Table 3-9: Inverter Connector Pinouts Figure 3-9: Inverte
Page 46 IEI® Technology, Corp. 3.2.8 Keyboard/Mouse Connector CN Label: KBMS1 CN Type: 6-pin header CN Pinouts: See Table 3-10 CN Location: See F
Page 47 PM-LX-800 CPU Card Figure 3-10: Keyboard/Mouse Connector Location 3.2.9 LAN Connector CN Label: LAN1 CN Type: 10-pin header (2x5 pins) CN
Page 48 IEI® Technology, Corp. PIN DESCRIPTION PIN DESCRIPTION 1 VCC3.3 6 ACTIVE 2 RX+ 7 RX- 3 LINK 8 GND 4 N/C 9 GND 5 TX+ 10 TX- Table 3
Page 49 PM-LX-800 CPU Card3.2.10 LED Power Connector CN Label: CN2 CN Type: 6-pin header CN Pinouts: See Table 3-12 CN Location: See Figure 3-12
PM-LX-800 CPU Card4.3.6 COM1/COM2 RS-232 Serial Port Installation... 72 4.3.7 COM3 RS-422/485 Serial Por
Page 50 IEI® Technology, Corp. Figure 3-12: LED Power Connector Location 3.2.11 Parallel Port Connector CN Label: LPT1 CN Type: 26-pin header
Page 51 PM-LX-800 CPU CardPIN DESCRIPTION PIN DESCRIPTION 1 STROBE# 14 AUTO FORM FEED # 2 DATA 0 15 ERROR# 3 DATA 1 16 INITIALIZE 4 DATA 2
Page 52 IEI® Technology, Corp. Figure 3-13: Parallel Port Connector Location 3.2.12 PCI-104 Connector CN Label: CN6A/B CN Type: PCI-104 connect
Page 53 PM-LX-800 CPU Card Pin A B C D 1 GROUND NC/SERIRQ +5V AD0 2 VIO AD2 AD1 +5V 3 AD5 GND AD4 AD3 4 CBE0- AD7 GND AD6 5 GND AD9
Page 54 IEI® Technology, Corp. Figure 3-14: PCI-104 Connector Location 3.2.13 RS-232 Serial Communications Connector CN Label: COM1, COM2 CN Type
Page 55 PM-LX-800 CPU Card PIN DESCRIPTION PIN DESCRIPTION 1 DCD# 6 DSR# 2 RX 7 RTS# 3 TX 8 CTS# 4 DTR# 9 RI# 5 GND 10 GND Table 3-15: RS-42
Page 56 IEI® Technology, Corp. 3.2.14 RS-422/485 Serial Communications Connector CN Label: CN10 CN Type: 4-pin header CN Pinouts: See Table 3-16
Page 57 PM-LX-800 CPU Card Figure 3-16 RS-422/485 Serial Communications Connector Locations 3.2.15 TTL LCD Connector CN Label: CN4 CN Type: 40-pin
Page 58 IEI® Technology, Corp. PIN DESCRIPTION PIN DESCRIPTION 8 GND 7 N/C 10 B1 9 B0 12 B3 11 B2 14 B5 13 B4 16 B7 15 B6 18 G1 17 G0 20
Page 59 PM-LX-800 CPU Card Figure 3-17 TTL LCD Connector Locations 3.2.16 USB Connector CN Label: USB1 CN Type: 8-pin header (2x4 pins) CN Pinouts
A BIOS CONFIGURATION OPTIONS ... 133 A.1 BIOS CONFIGURATION OPTIONS...
Page 60 IEI® Technology, Corp. PIN DESCRIPTION PIN DESCRIPTION 1 USBVCC1 2 GND 3 D1F- 4 D2F+ 5 D1F+ 6 D2F- 7 GND 8 USBVCC1 Table 3-18: USB
Page 61 PM-LX-800 CPU Card3.2.17 VGA Connector CN Label: VGA1 CN Type: 10-pin headers (2x5 pins) CN Pinouts: See Table 3-19 CN Location: See Figur
Page 62 IEI® Technology, Corp. Figure 3-19 VGA Connector Location 3.3 Onboard Jumpers NOTE: A jumper is a metal bridge used to close an elect
Page 63 PM-LX-800 CPU Card Figure 3-21: Jumper Locations NOTE: The PM-LX-800 does not provide a “Clear CMOS” configuration jumper. If the system
Page 64 IEI® Technology, Corp. 3.3.1 COM3 RS422/RS485 Select Jumper Jumper Label: JP1 Jumper Type: 3-pin header Jumper Location: See Figure 3-21
Page 65 PM-LX-800 CPU CardChapter4 4 Installation and Configuration
Page 66 IEI® Technology, Corp. 4.1 Installation Considerations NOTE: The following installation notices and installation considerations should be
Page 67 PM-LX-800 CPU Card4.2 Unpacking NOTE: If any of the items listed below are missing when the PM-LX-800 motherboard is unpacked, do not proce
Page 68 IEI® Technology, Corp. 4.2.2 Checklist Please ensure the package contains the following items. 1 x PM-LX single board computer 1 x Mi
Page 69 PM-LX-800 CPU CardThe following components must be installed onto the motherboard or connected to the motherboard during the installation pr
Page 7 PM-LX-800 CPU CardList of Figures Figure 1-1: PM-LX-800 Motherboard Overview (Front Side)...15 Figure 1-2: P
Page 70 IEI® Technology, Corp. Figure 4-1: SO-DIMM Module Installation 4.3.2 Compact Flash Disk Installation When appropriately formatted, a Com
Page 71 PM-LX-800 CPU CardQuantity Type 1 USB cable 1 VGA cable 1 LAN cable 1 Power cable Table 4-1: IEI Provided Cables 4.3.4 IDE Disk Drive Insta
Page 72 IEI® Technology, Corp. 4.3.5 Chassis LED Installation To connect the chassis LED to the motherboard, follow the instructions below. Step 1:
Page 73 PM-LX-800 CPU Card4.3.8 Keyboard/Mouse Installation The cable used to connect the motherboard to a keyboard or mouse is a 6-pin header to PS
Page 74 IEI® Technology, Corp. 4.3.11 LPT Port Installation To connect an LPT port to the motherboard, follow the instructions below. Step 1: Step
Page 75 PM-LX-800 CPU CardStep 3: Step 1: Step 2: Step 3: Connect the other end of the cable to standard USB connectors.Step 0: 4.3.15 VGA Port Inst
Page 76 IEI® Technology, Corp. through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply c
Page 77 PM-LX-800 CPU CardChapter5 5 Award BIOS Setup
Page 78 IEI® Technology, Corp. 5.1 Introduction A licensed copy of Phoenix Award BIOS is preprogrammed into the ROM BIOS. The BIOS setup program al
Page 79 PM-LX-800 CPU CardKey Function F5 Previous values for the page menu items F6 Fail-safe defaults for the current page menu items F7 Optim
Figure 6-2: AMD LX/GX CD Driver Menu... 120 Figure 6-3: Access Windows Control Panel...
Page 80 IEI® Technology, Corp. 5.1.5 Main BIOS Menu Once the BIOS opens, the main menu (BIOS Menu 1) appears. BIOS Menu 1: AwardBIOS CMOS Setup Uti
Page 81 PM-LX-800 CPU CardThe following user configurable options are also available in BIOS Menu 1: Load Fail-Safe Defaults Select this option t
Page 82 IEI® Technology, Corp. 5.2 Standard CMOS Features Use the Standard CMOS Features BIOS menu (BIOS Menu 2) to set basic BIOS configuration op
Page 83 PM-LX-800 CPU CardIDE device configurations are changed or set in the IDE Configuration menu (BIOS Menu 3). If an IDE device is detected, an
Page 84 IEI® Technology, Corp. Base Memory: The Base Memory is NOT user configurable. The POST determines the amount of base (or conventional)
Page 85 PM-LX-800 CPU Card5.2.1 IDE Primary Master/Slave Use the IDE Primary Master/Slave menu (BIOS Menu 3) to set or change the master/slave IDE c
Page 86 IEI® Technology, Corp. None If no drives are connected to the IDE channel select this option. Once set, this IDE channel becomes inacce
Page 87 PM-LX-800 CPU Card Cylinder The Cylinder specification indicates how many cylinders (tracks) are on the HDD installed in the system. He
Page 88 IEI® Technology, Corp. 5.3 Advanced BIOS Features CPU and peripheral device configuration options are accessed in the Advanced BIOS Feature
Page 89 PM-LX-800 CPU Card Enabled Activates automatically when the system boots up causing a warning message to appear when anything attempts to
Page 9 PM-LX-800 CPU CardList of Tables Table 1-1: Technical Specifications ...
Page 90 IEI® Technology, Corp. First Boot Device [Default: Floppy] Second Boot Device [Default: HDD-0] Third Boot Device [Default: CDROM]
Page 91 PM-LX-800 CPU Card Boot Up Floppy Seek [Disabled] Use the Boot Up Floppy Seek option to enable the BIOS to determine if the floppy disk dr
Page 92 IEI® Technology, Corp. down, it begins to report that the key has been pressed repeatedly. This feature accelerates cursor movement with th
Page 93 PM-LX-800 CPU Card Security Option [Setup] Use the Security Option to limit access to both the system and Setup, or just Setup. Setup (D
Page 94 IEI® Technology, Corp. Small Logo (EPA) Show [Disabled] Use the Small Logo (EPA) Show option to specify if the Environmental Protection
Page 95 PM-LX-800 CPU Card5.4 Advanced Chipset Features Use the Advanced Chipset Features menu (BIOS Menu 5) to change chipset configuration options
Page 96 IEI® Technology, Corp. CAS Latency [Auto] Use the CAS Latency Time option to set the Column Address Strobe (CAS) delay time. The CAS Lat
Page 97 PM-LX-800 CPU Card Output Display [CRT] Use the Output Display configuration to specify the display devices the system is connected to. Th
Page 98 IEI® Technology, Corp. 5.4.1 Flat Panel Configuration Use the Flat Panel Configuration menu (BIOS Menu 6) to set the configuration settings
Page 99 PM-LX-800 CPU Card 320 x 240 640 x 480 800 x 600 (Default) 1024 x 768 1152 x 864 1280 x 1024 1600 x 1200 Data Bus Typ
Comments to this Manuals