Iei-integration AFL-F08A v2.10 User Manual

AFL-F08A-N270 Panel PC Page iIEI Technology Corp. User Manual MODEL: AFL-F08A-N270 Fanless All-in-one Panel PC with 1.6 GHz Intel® Atom™ ProcessorT

AFL-F08A-N270 Panel PCPage x 177H177HFigure A-32: Restore System Backup Complete Window... 464H464

AFL-F08A-N270 Panel PCPage 88 Appendix B B One Key Recovery

AFL-F08A-N270 Panel PC Page 89B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system bac

AFL-F08A-N270 Panel PCPage 90 B.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and

AFL-F08A-N270 Panel PC Page 91 NOTE: Specialized tools are required to change the partition size if the operating system is already installed. B.1.

AFL-F08A-N270 Panel PCPage 92 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. B.2 Setup Procedure for Windows Prior

AFL-F08A-N270 Panel PC Page 93Step 4: Turn on the system. Step 5: Press the <DELETE> key as soon as the system is turned on to enter the BIO

AFL-F08A-N270 Panel PCPage 94 Step 3: The recovery tool setup menu is shown as below. Figure B-3: Recovery Tool Setup Menu Step 4: Press <5>

AFL-F08A-N270 Panel PC Page 95system32>format F: /fs:ntfs /q /v:Recovery /y system32>exit Figure B-5: Partition Creation Commands

AFL-F08A-N270 Panel PCPage 96 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to exi

AFL-F08A-N270 Panel PC Page 97B.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3:

AFL-F08A-N270 Panel PC Page xiList of Tables 179H179HTable 1-1: AFL-F08A-N270 System Specifications...

AFL-F08A-N270 Panel PCPage 98 recovery files in Section 775H775H632H632HB.2.2 is hidden and the recovery tool is saved in this partition. Figure B-

AFL-F08A-N270 Panel PC Page 99B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a

AFL-F08A-N270 Panel PCPage 100 Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (778H778H635H635HF

AFL-F08A-N270 Panel PC Page 101Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in 780

AFL-F08A-N270 Panel PCPage 102 Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in 782H782H639H639HFigure B-17 promp

AFL-F08A-N270 Panel PC Page 103Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creatio

AFL-F08A-N270 Panel PCPage 104 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step 0: Figur

AFL-F08A-N270 Panel PC Page 105 NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-22: Partitions for Linux St

AFL-F08A-N270 Panel PCPage 106 Figure B-23: System Configuration for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”.

AFL-F08A-N270 Panel PC Page 107 Step 7: The recovery tool menu appears. (788H788H645H645HFigure B-25) Figure B-25: Recovery Tool Menu Step 8: Cre

AFL-F08A-N270 Panel PCPage xii BIOS Menus 195H195HBIOS Menu 1: Main ...

AFL-F08A-N270 Panel PCPage 108 Figure B-26: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore

AFL-F08A-N270 Panel PC Page 109B.4.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> an

AFL-F08A-N270 Panel PCPage 110 B.4.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Enter&

AFL-F08A-N270 Panel PC Page 111B.4.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3&

AFL-F08A-N270 Panel PCPage 112 B.4.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press <

AFL-F08A-N270 Panel PC Page 113B.5 Other Information B.5.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode or

AFL-F08A-N270 Panel PCPage 114 Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Step 6: In the f

AFL-F08A-N270 Panel PC Page 115Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu. Continue to follow the

AFL-F08A-N270 Panel PCPage 116 Appendix C C Watchdog Timer

AFL-F08A-N270 Panel PC Page 117 NOTE: The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other op

AFL-F08A-N270 Panel PC Page 1Chapter 1 1 Introduction

AFL-F08A-N270 Panel PCPage 118 NOTE: The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer m

AFL-F08A-N270 Panel PC Page 119Appendix D D Safety Precautions

AFL-F08A-N270 Panel PCPage 120 WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions m

AFL-F08A-N270 Panel PC Page 121D.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the AFL-F08A-N270

AFL-F08A-N270 Panel PCPage 122  Outside the European Union - If you wish to dispose of used electrical and electronic products outside the Europea

AFL-F08A-N270 Panel PC Page 123 Avoid eating, drinking and smoking within vicinity of the AFL-F08A-N270. D.2.2 Cleaning Tools Some components in t

AFL-F08A-N270 Panel PCPage 124 Appendix E E Hazardous Materials Disclosure

AFL-F08A-N270 Panel PC Page 125E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercur

AFL-F08A-N270 Panel PCPage 126 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(CR(VI)) P

AFL-F08A-N270 Panel PC Page 127此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短

AFL-F08A-N270 Panel PCPage 2 1.1 Overview Figure 1-1: AFL-F08A-N270 Flat Panel PC The AFL-F08A-N270 is an 8" panel PC with a frameless front p

AFL-F08A-N270 Panel PCPage 128 Appendix F F Terminology

AFL-F08A-N270 Panel PC Page 129AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and

AFL-F08A-N270 Panel PCPage 130 DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directl

AFL-F08A-N270 Panel PC Page 131LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a li

AFL-F08A-N270 Panel PC Page 31.2 Features There are four models in the AFL-F08A-N270. Both models feature the following:  1.6 GHz Intel® Atom™ N27

AFL-F08A-N270 Panel PCPage 4 1.4 Rear Panel The rear panel provides access to retention screw holes that support the wall mounting. Refer to 507H507

AFL-F08A-N270 Panel PC Page 5 Figure 1-4: AFL-F08A-N270 I/O Interface Connector Panel 1.6 Internal Overview The AFL-F08A-N270 has the following comp

AFL-F08A-N270 Panel PCPage 6 Specification Description SSD CF Type II slot Watchdog Timer Software Programmable supports 1 sec. ~ 255 sec. syste

AFL-F08A-N270 Panel PC Page 71.8 Dimensions The dimensions are shown below. Figure 1-5: Main Dimensions

AFL-F08A-N270 Panel PCPage ii Revision Date Version Changes 22 July, 2011 2.10 Updated for R21 version (changed wireless module) 16 September, 201

AFL-F08A-N270 Panel PCPage 8 Figure 1-6: Rear Dimensions

AFL-F08A-N270 Panel PC Page 9Chapter 2 2 Unpacking

AFL-F08A-N270 Panel PCPage 10 To unpack the flat panel PC, follow the steps below: WARNING! The front side LCD screen has a protective plastic cove

AFL-F08A-N270 Panel PC Page 11Quantity Item Image 1 Power adapter 1 Power cord 1 Screw kit 1 User manual CD and driver CD 1 Touch pen (AFL-F

AFL-F08A-N270 Panel PCPage 12 Item Image Stand (P/N:STAND-A08) Arm (P/N: ARM-11-RS) Arm (P/N: ARM-31-RS) Table 2-2: Optional Items If any of the

AFL-F08A-N270 Panel PC Page 13Chapter 3 3 Installation

AFL-F08A-N270 Panel PCPage 14 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the AFL-F08A-N270 may

AFL-F08A-N270 Panel PC Page 15 Anti-static Discharge: If a user open the rear panel of the flat panel PC, to configure the jumpers or plug in adde

AFL-F08A-N270 Panel PCPage 16 Step 1: Remove the retention screws and lift the cover off the flat panel PC. Figure 3-1: Back Cover Retention Scr

AFL-F08A-N270 Panel PC Page 17Step 1: Undo the CompactFlash® cover fastening screw. Figure 3-3: CompactFlash® Card Cover Step 2: Slide the Comp

AFL-F08A-N270 Panel PC Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to imp

AFL-F08A-N270 Panel PCPage 18 Step 1: Undo the fastening screws indicated by the arrows and circles below. Figure 3-5: Internal Cover Removal Step

AFL-F08A-N270 Panel PC Page 193.7 Jumper Settings NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or thr

AFL-F08A-N270 Panel PCPage 20 3.7.2 Preconfigured Jumpers WARNING: Do not change the settings on the jumpers in described here. Doing so may disabl

AFL-F08A-N270 Panel PC Page 21 Figure 3-7: AT/ATX Power Selection Switch 3.7.4 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 2-pin header Ju

AFL-F08A-N270 Panel PCPage 22 Clear CMOS Description Short 1 - 2 Keep CMOS Setup Default Short 2 - 3 Clear CMOS Setup Table 3-3: Clear CMOS

AFL-F08A-N270 Panel PC Page 23JP10 Description Short 1-2 COM3 RI Pin use +12 V Short 3-4 COM3 RI Pin use RI Default Short 5-6 COM3 RI Pi

AFL-F08A-N270 Panel PCPage 24 Pin 2 Data+ Table 3-7: RS-485 Pinouts 3.7.6 COM3 RX Function Select Jumper Jumper Label: JP9 Jumper Type: 8-pin h

AFL-F08A-N270 Panel PC Page 253.7.7 COM3 TX Function Select Jumper Jumper Label: JP11 Jumper Type: 6-pin header Jumper Settings: See 525H525HTable

AFL-F08A-N270 Panel PCPage 26 3.7.8 COM3 RS-232/422/485 Serial Port Select Jumper Jumper Label: JP6 Jumper Type: 12-pin header (four 3-pin headers

AFL-F08A-N270 Panel PC Page 27 Figure 3-12: COM3 RS-232/422/485 Serial Port Select Jumper Location 3.8 Mounting the System WARNING! When mounting t

AFL-F08A-N270 Panel PCPage iv Table of Contents 01 INTRODUCTION...

AFL-F08A-N270 Panel PCPage 28 Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot holes and tight

AFL-F08A-N270 Panel PC Page 29Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket. Step 8: Carefull

AFL-F08A-N270 Panel PCPage 30 Figure 3-15: Secure the Panel PC 3.8.2 Panel Mounting To mount the AFL-F08A-N270 into a panel, please follow the step

AFL-F08A-N270 Panel PC Page 31 Figure 3-16: Tighten the Panel Mounting Clamp Screws 3.8.3 Arm Mounting The AFL-F08A-N270 is VESA (Video Electronics

AFL-F08A-N270 Panel PCPage 32 Step 3: Align the retention screw holes on the mounting arm interface with those in the flat panel PC. Figure 3-17:

AFL-F08A-N270 Panel PC Page 33 Figure 3-18: The Rack/Cabinet Bracket Step 2: Insert the rack mounting clamps into the pre-formed holes along the ed

AFL-F08A-N270 Panel PCPage 34 Figure 3-20: Install into a Rack/Cabinet Step 5: Once the AFL-F08A-N270 with the attached rack/cabinet bracket has b

AFL-F08A-N270 Panel PC Page 35 Figure 3-21: LAN Connection Step 3: Insert the LAN cable RJ-45 connector. Once aligned, gently insert the LAN cable

AFL-F08A-N270 Panel PCPage 36 Figure 3-22: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the externa

AFL-F08A-N270 Panel PC Page 373.9.2.2 COM3 Pinouts The pinouts for COM3 are listed in the table below. Pin RS-232 RS-422 RS-485 1 NDCDB TX- D- 2 NR

AFL-F08A-N270 Panel PC Page v29H29H3.8.2 Panel Mounting...

AFL-F08A-N270 Panel PCPage 38 Step 2: Align the connectors. Align the USB device connector with one of the connectors on the bottom panel. Figure

AFL-F08A-N270 Panel PC Page 39Chapter 4 4 System Maintenance

AFL-F08A-N270 Panel PCPage 40 4.1 System Maintenance Introduction If the components of the AFL-F08A-N270 fail they must be replaced. Components that

AFL-F08A-N270 Panel PC Page 41 Only handle the edges of the PCB: - When handling the PCB, hold the PCB by the edges. 4.3 Turn off the Power WARNI

AFL-F08A-N270 Panel PCPage 42 Figure 4-1: AFL-F08A-N270 SO-DIMM Socket Location Step 2: Remove the DDR memory module by pulling both the spring re

AFL-F08A-N270 Panel PC Page 43 Figure 4-2: DDR SO-DIMM Module Installation 4.5.2 CF Card Replacement To install the CompactFlash® card, the cover

AFL-F08A-N270 Panel PCPage 44 Step 2: Slide the CompactFlash® card into the slot under the cover. Figure 4-4: CompactFlash® Install Step 3: Once

AFL-F08A-N270 Panel PC Page 45Step 1: Insert the CD-ROM that came with the system into a CD-ROM drive attached to the system. Step 2: Click AFLMB-

AFL-F08A-N270 Panel PCPage 46 Chapter 5 5 BIOS

AFL-F08A-N270 Panel PC Page 475.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system se

AFL-F08A-N270 Panel PCPage vi 62H62H5.3.5 Power Configuration...

AFL-F08A-N270 Panel PCPage 48 Key Function F10 key Save all the CMOS changes, only for Main Menu Table 5-1: BIOS Navigation Keys 5.1.3 Getting H

AFL-F08A-N270 Panel PC Page 495.2 Main The Main menu gives an overview of the basic system information. BIOS SETUP UTILITY Main Advanced PCIPNP B

AFL-F08A-N270 Panel PCPage 50 The System Overview field also has two user configurable fields: Î System Time [xx:xx:xx] Use the System Time option

AFL-F08A-N270 Panel PC Page 51BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PCPage 52  Frequency: Lists the CPU processing speed  FSB Speed: Lists the FSB speed  Cache L1: Lists the CPU L1 cache siz

AFL-F08A-N270 Panel PC Page 53Î Enhanced DEFAULT Configures the on-board ATA/IDE controller to be in Enhanced mode. In this mode, IDE channels and S

AFL-F08A-N270 Panel PCPage 54 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Primary IDE Master ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PC Page 55 32Bit Data Transfer: Enables 32-bit data transfer. Î Type [Auto] Use the Type BIOS option select the type of devic

AFL-F08A-N270 Panel PCPage 56 Î Block (Multi Sector Transfer) [Auto] Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect

AFL-F08A-N270 Panel PC Page 57Î Auto DEFAULT BIOS auto detects the DMA mode. Use this value if the IDE disk drive support cannot be determined. Î SW

AFL-F08A-N270 Panel PC Page vii96H96HB.4.4 Manual...

AFL-F08A-N270 Panel PCPage 58 Î S.M.A.R.T [Auto] Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and Reporting

AFL-F08A-N270 Panel PC Page 59Î Serial Port 1 Address [3F8] Sets the port address and IRQ of serial port 1.  Disabled  3F8/IRQ4 DEFAULT  2F8/IR

AFL-F08A-N270 Panel PCPage 60  RS232 DEFAULT  RS422/RS485 Î Serial Port 4 Address [2E8] Sets the port address of serial port 4.  Disabled  2E8

AFL-F08A-N270 Panel PC Page 61BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Current Jumper Setting [ATX] > ACPI Con

AFL-F08A-N270 Panel PCPage 62 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit ACPI Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PC Page 63BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit APM Configuration ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PCPage 64 Î Resume on Ring [Disabled] Use the Resume on Ring BIOS option to enable activity on the RI (ring in) modem line to r

AFL-F08A-N270 Panel PC Page 65BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Configure Remote Access type and parameters

AFL-F08A-N270 Panel PCPage 66 NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu. Î Base Address, IRQ [2F8h,

AFL-F08A-N270 Panel PC Page 67Î Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type. Î ANSI DEFAULT The targ

AFL-F08A-N270 Panel PCPage viii List of Figures 112H112HFigure 1-1: AFL-F08A-N270 Flat Panel PC ...

AFL-F08A-N270 Panel PCPage 68 Î Disabled USB 2.0 controller disabled Î Enabled DEFAULT USB 2.0 controller enabled Î Legacy USB Support [Enabled] U

AFL-F08A-N270 Panel PC Page 69BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit USB Mass Storage Device Configuration ⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PCPage 70 Î Auto DEFAULT BIOS auto-detects the current USB. Î Floppy The USB device will be emulated as a floppy drive. The dev

AFL-F08A-N270 Panel PC Page 71BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced PCI/PnP Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PCPage 72  IRQ9  IRQ10  IRQ 11  IRQ 14  IRQ 15 Î Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option

AFL-F08A-N270 Panel PC Page 735.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (549H549HBIOS Menu 16) to configure advance

AFL-F08A-N270 Panel PCPage 74 Î AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) me

AFL-F08A-N270 Panel PC Page 75Î Spread Spectrum Function [Disabled] The Spread Spectrum Function option can help to improve CPU EMI issues. Î Disab

AFL-F08A-N270 Panel PCPage 76 5.5.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. Only installe

AFL-F08A-N270 Panel PC Page 775.5.4 Removable Drives Use the Removable Drives menu (550H550HBIOS Menu 19) to specify the boot sequence of the remova

AFL-F08A-N270 Panel PC Page ix142H142HFigure 4-2: DDR SO-DIMM Module Installation...

AFL-F08A-N270 Panel PCPage 78 The boot sequence from the available devices is selected. If the “1st Drive” option is selected a list of available CD

AFL-F08A-N270 Panel PC Page 79Î Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default f

AFL-F08A-N270 Panel PCPage 80 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PC Page 81Î Memory Hole [Disabled] Use the Memory Hole option to reserve memory space between 15 MB and 16 MB for ISA expansion

AFL-F08A-N270 Panel PCPage 82 Î DVMT Mode DEFAULT Graphics memory is dynamically allocated according to the system and graphics needs. Î Combo Mode

AFL-F08A-N270 Panel PC Page 835.7.2 Southbridge Configuration The Southbridge Configuration menu the Southbridge chipset to be configured. BIOS SETU

AFL-F08A-N270 Panel PCPage 84 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Exit Exit Options ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL-F08A-N270 Panel PC Page 85Appendix A A BIOS Options

AFL-F08A-N270 Panel PCPage 86 Below is a list of BIOS configuration options in the BIOS chapter. 220H220H　 System Overview ...

AFL-F08A-N270 Panel PC Page 87253H253H　 Terminal Type [ANSI]......................