Iei-integration AFL2-W15A-N270 v2.00 User Manual

AFL2-W15A-N270 Panel PC Page iUser Manual MODEL: AFL2-W15A-N270 Panel PC with Intel®Atom™ N270 CPU, Touchscreen Gigabit Ethernet, USB, Audio, RS-23

AFL2-W15A-N270 Panel PCPage x Figure B-30: System Backup Complete Window ... 108 Fig

AFL2-W15A-N270 Panel PCPage 88 B.1.1 System Requirement NOTE: The recovery CD can only be used with IEI products. The software will fail to run and

AFL2-W15A-N270 Panel PC Page 89 NOTE: Specialized tools are required to change the partition size if the operating system is already installed. B.1

AFL2-W15A-N270 Panel PCPage 90 NOTE: Installing unsupported OS versions may cause the recovery tool to fail. B.2 Setup Procedure for Windows Prior

AFL2-W15A-N270 Panel PC Page 91Step 4: Turn on the system. Step 5: Press the <DELETE> key as soon as the system is turned on to enter the BI

AFL2-W15A-N270 Panel PCPage 92 Step 3: The recovery tool setup menu is shown as below. Figure B-3: Recovery Tool Setup Menu Step 4: Press <5&g

AFL2-W15A-N270 Panel PC Page 93system32>format F: /fs:ntfs /q /v:Recovery /y system32>exit Figure B-5: Partition Creation Commands

AFL2-W15A-N270 Panel PCPage 94 NOTE: Use the following commands to check if the partitions were created successfully. Step 6: Press any key to ex

AFL2-W15A-N270 Panel PC Page 95B.2.4 Build-up Recovery Partition Step 1: Put the recover CD in the optical drive. Step 2: Start the system. Step 3

AFL2-W15A-N270 Panel PCPage 96 recovery files in Section 75B.2.2 is hidden and the recovery tool is saved in this partition. Figure B-8: Build-up R

AFL2-W15A-N270 Panel PC Page 97B.2.5 Create Factory Default Image NOTE: Before creating the factory default image, please configure the system to a

AFL2-W15A-N270 Panel PC Page xiList of Tables Table 1-1: Model Variations...

AFL2-W15A-N270 Panel PCPage 98 Figure B-12: About Symantec Ghost Window Step 4: Use mouse to navigate to the option shown below (75Figure B-13).

AFL2-W15A-N270 Panel PC Page 99Figure B-14: Select a Local Source Drive Step 6: Select a source partition (Part 1) from basic drive as shown in 75F

AFL2-W15A-N270 Panel PCPage 100 Figure B-16: File Name to Copy Image to Step 8: When the Compress Image screen in 75Figure B-17 prompts, click Hig

AFL2-W15A-N270 Panel PC Page 101Step 9: The Proceed with partition image creation window appears, click Yes to continue. Figure B-18: Image Creati

AFL2-W15A-N270 Panel PCPage 102 Step 12: The recovery tool main menu window is shown as below. Press any key to reboot the system. Step 0: Figu

AFL2-W15A-N270 Panel PC Page 103 NOTE: Please reserve enough space for partition 3 for saving recovery images. Figure B-22: Partitions for Linux S

AFL2-W15A-N270 Panel PCPage 104 Figure B-23: System Configuration for Linux Step 5: Access the recovery tool main menu by modifying the “menu.lst”

AFL2-W15A-N270 Panel PC Page 105 Step 7: The recovery tool menu appears. (76Figure B-25) Figure B-25: Recovery Tool Menu Step 8: Create a factory

AFL2-W15A-N270 Panel PCPage 106 Figure B-26: Recovery Tool Main Menu The recovery tool has several functions including: 1. Factory Restore: Restore

AFL2-W15A-N270 Panel PC Page 107B.4.1 Factory Restore To restore the factory default image, please follow the steps below. Step 1: Type <1> a

AFL2-W15A-N270 Panel PCPage xii BIOS Menus BIOS Menu 1: Main ...

AFL2-W15A-N270 Panel PCPage 108 B.4.2 Backup System To backup the system, please follow the steps below. Step 1: Type <2> and press <Enter

AFL2-W15A-N270 Panel PC Page 109B.4.3 Restore Your Last Backup To restore the last system backup, please follow the steps below. Step 1: Type <3

AFL2-W15A-N270 Panel PCPage 110 B.4.4 Manual To restore the last system backup, please follow the steps below. Step 1: Type <4> and press <

AFL2-W15A-N270 Panel PC Page 111B.5 Other Information B.5.1 Using AHCI Mode or ALi M5283 / VIA VT6421A Controller When the system uses AHCI mode o

AFL2-W15A-N270 Panel PCPage 112 Step 5: When the following window appears, press <S> to select “Specify Additional Device”. Step 6: In the

AFL2-W15A-N270 Panel PC Page 113Step 7: After pressing <Enter>, the system will get into the recovery tool setup menu. Continue to follow the

AFL2-W15A-N270 Panel PCPage 114 Appendix C C BIOS Options

AFL2-W15A-N270 Panel PC Page 115Below is a list of BIOS configuration options in the BIOS chapter. 　 System Overview ...

AFL2-W15A-N270 Panel PCPage 116 　 USB Configuration...

AFL2-W15A-N270 Panel PC Page 117Appendix D D Terminology

AFL2-W15A-N270 Panel PC Page 1Chapter 1 1 Introduction

AFL2-W15A-N270 Panel PCPage 118 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration an

AFL2-W15A-N270 Panel PC Page 119DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate direct

AFL2-W15A-N270 Panel PCPage 120 LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a l

AFL2-W15A-N270 Panel PC Page 121Appendix E E Watchdog Timer

AFL2-W15A-N270 Panel PCPage 122 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for

AFL2-W15A-N270 Panel PC Page 123 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example p

AFL2-W15A-N270 Panel PCPage 124 Appendix F F Hazardous Materials Disclosure

AFL2-W15A-N270 Panel PC Page 125F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercu

AFL2-W15A-N270 Panel PCPage 126 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (CR(VI)

AFL2-W15A-N270 Panel PC Page 127此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较

AFL2-W15A-N270 Panel PCPage 2 1.1 Overview Figure 1-1: AFL2-W15A-N270 The Afolux panel PCs are all-in-one panel PCs with all the elements of a desk

AFL2-W15A-N270 Panel PCPage 128 Appendix G G International Standards Compliance

AFL2-W15A-N270 Panel PC Page 129G.1 EN 60601-1, EN 60601-2 The LCD monitor complies with the EN 60601-1 and EN 60601-2 of related European standa

AFL2-W15A-N270 Panel PC Page 31.2 Model Variations There are two models of the AFL2-W15A-N270 series. The model variations are listed below. Model C

AFL2-W15A-N270 Panel PCPage 4 1.4 External Overview The AFL2-W15A-N270 consists of a screen and rear panel that covers the back, sides and top. The

AFL2-W15A-N270 Panel PC Page 5 Figure 1-3: Rear Panel 1.4.3 Bottom Panel The bottom panel has the following slots, buttons and switches:  1 x Audi

AFL2-W15A-N270 Panel PCPage 6 Figure 1-4: AFL2-W15A-N270 Bottom Panel 1.5 Internal Overview All the components are contained under the rear panel.

AFL2-W15A-N270 Panel PC Page 71.6 Specifications The technical specifications for the AFL2-W15A-N270 systems are listed in Table 1-2. SPECIFICATIONS

AFL2-W15A-N270 Panel PCPage ii Revision Date Version Changes 29 August 2013 2.00 Updated for R20 version 28 June, 2013 1.01 Updated Section 2.8:

AFL2-W15A-N270 Panel PCPage 8 SPECIFICATIONS AFL2-W15A-N270/R/1G-R20 AFL2-W15A-N270/PC/1G-R20 I/O 1 x Gigabit LAN 1 x Audio line-out 1 x Power in

AFL2-W15A-N270 Panel PC Page 91.7 Dimensions Width: 400 mm; Height: 267 mm; Depth: 54 mm. Figure 1-5: Dimensions

AFL2-W15A-N270 Panel PCPage 10 Chapter 2 2 Installation

AFL2-W15A-N270 Panel PC Page 11 WARNING: When installing the AFL2-W15A-N270, make sure to:  Turn the power off: Chance of electrocution. Turn off

AFL2-W15A-N270 Panel PCPage 12 2.1 Unpack the Panel PC To unpack the flat panel PC, follow the steps below: WARNING! Only remove the protective pla

AFL2-W15A-N270 Panel PC Page 13Quantity Item Image 1 Power cord 4 Screws 1 HDD bracket 1 Touch screen pen 1 Remote Control 1 Utility CD

AFL2-W15A-N270 Panel PCPage 14 Figure 2-1: HDD Access Panel Retention Screws Step 2: Locate the HDD/CF card brackets. Unfasten screws and removed

AFL2-W15A-N270 Panel PC Page 15 Figure 2-3: HDD Bracket Retention Screws Step 4: Insert the SATA connector end of the HDD into the bracket to conne

AFL2-W15A-N270 Panel PCPage 16 2.4 CompactFlash® Installation The installation for a CompactFlash® card is described in this section. Step 1: Rem

AFL2-W15A-N270 Panel PC Page 172.5 USB Dongle Installation The installation for an USB dongle is described in this section. Step 1: Remove the ac

AFL2-W15A-N270 Panel PC Page iiiCopyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to im

AFL2-W15A-N270 Panel PCPage 18 WARNING! Take antistatic precautions when working on the internal components. Some internal components are easily d

AFL2-W15A-N270 Panel PC Page 19 Figure 2-9: Internal Aluminum Cover Retention Screws 2.7 Jumper Settings NOTE: A jumper is a metal bridge used

AFL2-W15A-N270 Panel PCPage 20 Description Label Type CF card setup JCF1 2-pin header Clear CMOS J_CMOS1 3-pin header COM1 Pin 9 setting JP5

AFL2-W15A-N270 Panel PC Page 21 Figure 2-10: CF Card Setup Jumper Location 2.7.3 Clear CMOS Jumper Jumper Label: J_CMOS1 Jumper Type: 3-pin header

AFL2-W15A-N270 Panel PCPage 22 Clear CMOS Description Short 1 - 2 Keep CMOS Setup (Default) Short 2 - 3 Clear CMOS Setup Table 2-4: Clear CMOS J

AFL2-W15A-N270 Panel PC Page 23Short 7-9 COM1 RI Pin use +5 V (Default) Table 2-5: COM1 Pin 9 Setting Jumper Settings The COM1 Pin 9 Setting jumper

AFL2-W15A-N270 Panel PCPage 24 Short 5-6 COM3 RI Pin use +5 V Table 2-6: COM3 Pin 9 Setting Jumper Settings The COM3 Pin 9 Setting jumper locations

AFL2-W15A-N270 Panel PC Page 25Short 7-8 RS-485 Table 2-7: COM3 RX Function Select Jumper Settings The COM3 RX Function Select jumper location is s

AFL2-W15A-N270 Panel PCPage 26 Table 2-8: COM3 RS-232/422/485 Serial Port Select Jumper Settings The COM3 RS-232/422/485 Serial Port Select jumper l

AFL2-W15A-N270 Panel PC Page 27Short 4 – 6 RS-485 D+ Table 2-9: COM3 TX Function Select Jumper Settings The COM3 TX Function Select jumper location

AFL2-W15A-N270 Panel PCPage iv Table of Contents 1 INTRODUCTION...

AFL2-W15A-N270 Panel PCPage 28 2.8 Mounting the System WARNING! The panel PC is very heavy. Two or more people should mount the panel PC. Dropping

AFL2-W15A-N270 Panel PC Page 29Step 2: Once the mounting arm has been firmly attached to its surface, lift the AFL2-W15A-N270 onto the interface pa

AFL2-W15A-N270 Panel PCPage 30 Figure 2-18: Arm Mounting (ARM-11-RS) 2.8.2 Panel Mounting To mount the panel PC into a panel, please follow the st

AFL2-W15A-N270 Panel PC Page 31 Figure 2-19: Cutout Step 3: Slide the flat panel PC through the hole until the aluminum frame is flush against the

AFL2-W15A-N270 Panel PCPage 32 Figure 2-20: Tighten the Panel Mounting Clamp Screws 2.8.3 Stand Mounting To mount the AFL2-W15A-N270 using the stan

AFL2-W15A-N270 Panel PC Page 33 Figure 2-21: Stand Mounting (Stand-A19) 2.8.4 Wall Mounting To mount the flat panel PC onto the wall, please follow

AFL2-W15A-N270 Panel PCPage 34 Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws. Step 4: Align

AFL2-W15A-N270 Panel PC Page 35 Figure 2-24: Chassis Support Screws NOTE: In the diagram below the bracket is already installed on the wall. Step

AFL2-W15A-N270 Panel PCPage 36 Figure 2-25: Secure the Panel PC 2.9 Bottom Panel Connectors The bottom panel connectors extend the capabilities of

AFL2-W15A-N270 Panel PC Page 372.9.1 LAN Connection The RJ-45 connector enables connection to an external network. To connect a LAN cable with an

AFL2-W15A-N270 Panel PC Page v2.8.2 Panel Mounting... 3

AFL2-W15A-N270 Panel PCPage 38 Figure 2-28: Serial Device Connector Step 3: Secure the connector. Secure the serial device connector to the extern

AFL2-W15A-N270 Panel PC Page 39Step 3: Insert the device connector. Once aligned, gently insert the USB device connector into the onboard connector

AFL2-W15A-N270 Panel PCPage 40 2.10 Power Connection The power cable connects the panel PC to the power supply. The power cable is required for oper

AFL2-W15A-N270 Panel PC Page 41Chapter 3 3 BIOS Setup

AFL2-W15A-N270 Panel PCPage 42 3.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system s

AFL2-W15A-N270 Panel PC Page 43Key Function F2 /F3 key Change color from total three colors. F2 to select color forward. F10 key Save all the

AFL2-W15A-N270 Panel PCPage 44 3.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an over

AFL2-W15A-N270 Panel PC Page 45The System Overview field also has two user configurable fields:  System Time [xx:xx:xx] Use the System Time option

AFL2-W15A-N270 Panel PCPage 46 3.3.1 CPU Configuration Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications and configur

AFL2-W15A-N270 Panel PC Page 47 3.3.2 IDE Configuration Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration of the I

AFL2-W15A-N270 Panel PCPage vi 3.5.3 Hard Disk Drives ...

AFL2-W15A-N270 Panel PCPage 48  Legacy IDE Channels [SATA Pri, PATA Sec]  SATA Only Only the SATA drives are enabled.  SATA Pri, PATA Sec DEF

AFL2-W15A-N270 Panel PC Page 49 LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a method of addressing data on a disk drive is s

AFL2-W15A-N270 Panel PCPage 50  LBA/Large Mode [Auto] Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical Block A

AFL2-W15A-N270 Panel PC Page 51 3 PIO mode 3 selected with a maximum transfer rate of 11.1 MB/s 4 PIO mode 4 selected with a maximum transfer ra

AFL2-W15A-N270 Panel PCPage 52 3.3.3 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 6) to set or change the configurations fo

AFL2-W15A-N270 Panel PC Page 53 2E8/IRQ3 I/O address 2E8 and interrupt address IRQ3  Serial Port3 Address [3E8] Selects the serial port base add

AFL2-W15A-N270 Panel PCPage 54 3.3.4 Hardware Health Configuration The Hardware Health Configuration menu (BIOS Menu 7) shows the operating tempera

AFL2-W15A-N270 Panel PC Page 55o VBAT 3.3.5 Power Configuration The Power Configuration menu (BIOS Menu 8) allows the advanced power management

AFL2-W15A-N270 Panel PCPage 56 3.3.5.1 ACPI Settings Use the ACPI Settings menu (BIOS Menu 9) to select the ACPI state when the system is suspended.

AFL2-W15A-N270 Panel PC Page 573.3.5.2 APM Configuration The APM Configuration menu (BIOS Menu 10) allows the advanced power management options to

AFL2-W15A-N270 Panel PC Page viiB.4.4 Manual...

AFL2-W15A-N270 Panel PCPage 58  Suspend When the power button is pressed the system goes into suspend mode  Resume on Keyboard/Mouse [Disabled]

AFL2-W15A-N270 Panel PC Page 59 Resume on LAN [Enabled] The Resume on LAN BIOS option specifies if the system is roused from a suspended or standb

AFL2-W15A-N270 Panel PCPage 60 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Configure Remote Access type and param

AFL2-W15A-N270 Panel PC Page 61NOTE: Make sure the selected COM port is enabled through the Super I/O configuration menu.  Base Address, IRQ [3F8h

AFL2-W15A-N270 Panel PCPage 62  Terminal Type [ANSI] Use the Terminal Type BIOS option to specify the remote terminal type.  ANSI DEFAULT The tar

AFL2-W15A-N270 Panel PC Page 63 USB Function [Enabled] Use the USB Function BIOS option to enable or disable USB function support.  Disabled USB

AFL2-W15A-N270 Panel PCPage 64 3.3.8 IEI Feature Use the IEI Feature menu (BIOS Menu 13) to configure One Key Recovery function. BIOS SETUP UTILITY

AFL2-W15A-N270 Panel PC Page 653.4 PCI/PnP Use the PCI/PnP menu (BIOS Menu 14) to configure advanced PCI and PnP settings. WARNING! Setting wrong v

AFL2-W15A-N270 Panel PCPage 66  Reserved The specified IRQ is reserved for use by Legacy ISA devices Available IRQ addresses are:  IRQ3  IRQ4 

AFL2-W15A-N270 Panel PC Page 67 Reserved Memory Size [Disabled] Use the Reserved Memory Size BIOS option to specify the amount of memory that shou

AFL2-W15A-N270 Panel PCPage viii List of Figures Figure 1-1: AFL2-W15A-N270 ...

AFL2-W15A-N270 Panel PCPage 68 3.5.1 Boot Settings Configuration Use the Boot Settings Configuration menu (BIOS Menu 16) to configure advanced syste

AFL2-W15A-N270 Panel PC Page 69 AddOn ROM Display Mode [Force BIOS] Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory) m

AFL2-W15A-N270 Panel PCPage 70  Spread Spectrum Mode [Disabled] The Spread Spectrum Mode option can help to improve CPU EMI issues.  Disabled D

AFL2-W15A-N270 Panel PC Page 713.5.3 Hard Disk Drives Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs. Only install

AFL2-W15A-N270 Panel PCPage 72  Change Supervisor Password Use the Change Supervisor Password to set or change a supervisor password. The default

AFL2-W15A-N270 Panel PC Page 73BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit Advanced Chipset Settings ⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

AFL2-W15A-N270 Panel PCPage 74  Memory Hole [Disabled] Use the Memory Hole option to reserve memory space between 15 MB and 16 MB for ISA expansio

AFL2-W15A-N270 Panel PC Page 75 DVMT/FIXED Memory [Maximum DVMT] Use the DVMT/FIXED Memory option to specify the maximum amount of memory that can

AFL2-W15A-N270 Panel PCPage 76 BIOS SETUP UTILITY Main Advanced PCIPNP Boot Security Chipset Power Exit South Bridge Chipset Configuration ⎯⎯

AFL2-W15A-N270 Panel PC Page 773.8 Exit Use the Exit menu (BIOS Menu 23) to load default BIOS values, optimal failsafe values and to save configurat

AFL2-W15A-N270 Panel PC Page ixFigure 2-26: AFL2-W15A-N270 Bottom Panel...3

AFL2-W15A-N270 Panel PCPage 78  Load Failsafe Defaults Use the Load Failsafe Defaults option to load failsafe default values for each of the param

AFL2-W15A-N270 Panel PC Page 79Chapter 4 4 System Maintenance

AFL2-W15A-N270 Panel PCPage 80 4.1 System Maintenance Introduction If the components of the AFL2-W15A-N270 fail they must be replaced, such as the w

AFL2-W15A-N270 Panel PC Page 81Appendix A A Safety Precautions

AFL2-W15A-N270 Panel PCPage 82 WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions m

AFL2-W15A-N270 Panel PC Page 83A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the AFL2-W15A-N270

AFL2-W15A-N270 Panel PCPage 84 A.1.3 Product Disposal CAUTION: Risk of explosion if battery is replaced by and incorrect type. Only certified engin

AFL2-W15A-N270 Panel PC Page 85 Except for the LCD panel, never spray or squirt liquids directly onto any other components. To clean the LCD panel

AFL2-W15A-N270 Panel PCPage 86 Appendix B B One Key Recovery

AFL2-W15A-N270 Panel PC Page 87B.1 One Key Recovery Introduction The IEI one key recovery is an easy-to-use front end for the Norton Ghost system ba